Publications Repository - Helmholtz-Zentrum Dresden-Rossendorf
Institute | Leading institute | |
---|---|
FS | FK | FW | FWI | FWP | FWK | FWO | FWD | FWH | FWG | FWM | FWU | FWZ | FWF | FWC | FKT | ||
Year | 2024 | 2023 | 2022 | 2021 | 2020 | 2019 | <=2018 | |
Type of publication | Articles ref. in Journals | Conference abstracts in ref. journals | Books | Proceedings | Wissenschaftlich-Technische Berichte/ HZDR-Reports | Lectures | Posters | Patents | Research data | Software | RODARE publications | |
Open Access | Yes | No | |
Search |
"Online First" included
Approved and published publications
Only approved publications
41875 Publications
Simplified method for electromagnetic detection of gas bubbles in liquid metals
Andreev, O.; Wondrak, T.; Gundrum, T.; Eckert, S.
Abstract
The AC electromagnetic induction is the most appropriate mechanism for monitoring of metallic objects and media with inhomogeneous distribution of electrical conductivity. In particular, the liquid metal flows with gas bubbles inside can be controlled by this method. In the present work we show a particular case when the series of 1D measurements can be applied for definition of position of a single gas bubble in y and z directions. The numerical experiment was made within a rectangular column filled with the liquid metal as it is shown in Figure (a). The basic AC (100 Hz) magnetic field was generated by a rectangular excitation coil. Typical distribution of the amplitude value of secondary magnetic field caused by a single bubble (5 mm) is shown in Fig.(c). The wall of measurement is opposite to the excitation coil. The shown normal component of magnetic field can generate an electrical signal in a measuring coil applied to the wall. In our experiment we use a system of rectangular coils stretched in horizontal and vertical directions (Fig. a,c).
A detector of such configuration averages the value of magnetic field flux within the long direction of the coil. Vice versa, a number of detectors can give the detailed information about distribution of magnetic field along the short sides of the coils. So far as the secondary magnetic field is presented by a dipolar structure (Fig. c) where the central singular point corresponds to position of the bubble, the signal collected from the series of coils has a zero point situated between two extremes (Fig. b, c). This zero point indicates position of the bubble. Thus, using a system of vertical and horizontal coils placed on the rear walls (Fig. a,c), one can estimate position of a single bubble in y and z directions according to two 1D distributions of the signal. In our numerical experiment a single bubble moves in vertical direction by a spiral trajectory (Fig. d). In Figure (e) we reconstruct the y and z coordinates of the bubble (red circles). The real positions of the bubble are marked by the small blue circles in this figure.
Keywords: liquid metal; two-phase flows; inductive method; bubble detection
-
Poster
3rd International Workshop on Measuring Techniques for Liquid Metal Flows (MTLM2015), 15.-17.4.2015, Dresden, Germany
Permalink: https://www.hzdr.de/publications/Publ-22929
2D velocity measurement using local Lorentz force velocimetry
Hernández, D.; Wondrak, T.; Schleichert, J.; Karcher, C.; Thess, A.
Abstract
Local velocity measurement of liquid metals continues to be an unsolved issue. Contact or even contactless measurement techniques cannot be used due to the fact that metal melts, like liquid steel, are usually at high temperatures, aggressive and opaque. Fortunately, there is a contactless velocity measurement technique called Lorentz force velocimetry in which a static magnetic field is applied on the electrically conductive metal stream. This static magnetic field is produced by permanent magnets, and if their size is smaller in comparison with the cross-section of the flow, a localized magnetic field distribution on the liquid metal is achieved. As a result and according to the principles of magnetohydrodynamics, eddy currents are generated within the liquid giving rise to a localized flow-breaking Lorentz force. Additionally and owing to Newtons third law, a force of the same magnitude but in the streamwise direction acts on the permanent magnet system which is connected to an optical interference force measurement device, giving access to local velocity information. This paper presents the results of local Lorentz force velocimetry at the mini-Limmcast facility at Helmholtz-Zentrum Dresden - Rosendorf using a 10mm cubic magnet and having as test fluid Galinstan in eutectic composition. In addition, partial results of Lorentz LFV using a multi-degree-of-freedom force/torque sensor are presented.
Keywords: Lorentz force velocimetry; liquid metal; flow measurement
-
Lecture (Conference)
3rd International Workshop on Measuring Techniques for Liquid Metal Flows (MTLM2015), 15.-17.4.2015, Dresden, Germany
Permalink: https://www.hzdr.de/publications/Publ-22928
Recent developments on the contactless inductive flow tomography
Wondrak, T.; Ratajczak, M.; Stefani, F.; Gundrum, T.; Timmel, K.; Pal, J.; Eckert, S.
Abstract
The Contactless Inductive Flow Tomography (CIFT) allows the reconstruction of the mean three dimensional flow structure in conducting liquids [1]. Exposing the liquid to one or multiple applied magnetic fields and measuring the flow induced magnetic field around the fluid volume, it is possible to infer the velocity field by solving a linear inverse problem with appropriate regularization techniques. One challenge is the reliable detection of the tiny flow induced perturbation of the applied magnetic field. Typically, the flow induced magnetic field is about 3 to 5 orders of magnitude smaller than the applied magnetic field, so that a measurement system with a high dynamic range is required.
We start with a short overview of the first demonstration experiment of CIFT [1]. In a cylindrical vessel filled with GaInSn a propeller generates a three dimensional flow structure with a maximum velocity of 1 m/s. The flow induced magnetic field is about 3 orders of magnitude smaller than the applied magnetic field.
One promising application for CIFT is the continuous casting of steel in which the flow structure in the mould is very important for the quality of the produced steel. For a model of a continuous slab caster operated with GaInSn we developed a measurement system consisting of one excitation coil around the mould and 14 magnetic field sensors [2]. In this industrially relevant setup the flow induced magnetic field is about 4 orders of magnitude smaller than the applied magnetic field. We were able to reconstruct different flow transitions in the mould in case that Argon was injected into the submerged entry nozzle (SEN) [3], and various effects of an electromagnetic stirrer at the SEN on the flow in the mould [3]. Recent developments concerned the reconstruction of the flow in the mould in the presence of a strong static magnetic field. Additionally, we show preliminary measurements at a modified Rayleigh-Bénard setup operated with GaInSn demonstrating the applicability of CIFT for thermally driven convection systems with velocities in the order of 0.01 m/s. Typical features of the thermally driven turbulent flow could be detected in the magnetic field measurements and were verified by simultaneous temperature measurements recorded by small thermocouples.
References
1. F. Stefani et al., Physical Review E, 70 (2004), 056306
2. T. Wondrak et al., Measurement Science & Technology 21 (2010), 045402
3. T. Wondrak et al., Metallurgical and Materials Transactions B 42 (2011), 1201-1210
Keywords: contactless inductive flow tomography; liquid metal; flow measurement; continuous casting
-
Lecture (Conference)
3rd International Workshop on Measuring Techniques for Liquid Metal Flows (MTLM2015), 15.-17.4.2015, Dresden, Germany
Permalink: https://www.hzdr.de/publications/Publ-22927
Electromagnetic interaction of a small magnet and liquid metal flow in a pipe with insulating or conducting walls
Kazak, O.; Heinicke, C.; Wondrak, T.; Boeck, T.
Abstract
We study the effects of electrically conducting walls on the interaction between a permanent magnet and a liquid-metal flow in a cylindrical pipe using experiments and numerical simulation. The problem is motivated by Lorentz force velocimetry, where the drag force on the magnet due to the induced eddy currents in the flow is used for flow measurement. Compared with insulating walls, the conducting walls lead to an increased drag force on the magnet. Except for low distances, the experimental results are satisfactorily reproduced in simulations using two different approximations of the magnetic field distribution.
Keywords: Lorentz force velocimetry; liquid metal; flow measurement
- Magnetohydrodynamics 51(2015), 579-588
Permalink: https://www.hzdr.de/publications/Publ-22926
Origin of Cu-Ni-PGE mineralization at the Manchego Prospect, West Musgrave Province, Western Australia
Karykowski, B. T.; Polito, P. A.; Maier, W. D.; Gutzmer, J.
Abstract
The late Mesoproterozoic Giles Complex of the West Musgrave province hosts one of the largest concentrations of mafic-ultramafic layered intrusions on Earth. Therefore, the area is highly prospective for hosting significant Ni-Cu and platinum-group element (PGE) mineralization, especially following the discovery of a large magmatic sulfide deposit at Nebo-Babel in 2000. More recently, a significant occurrence of massive to disseminated sulfide mineralization reaching up to 0.62 wt % Cu, 0.47 wt % Ni, and 1 ppm Pt + Pd was identified at the Manchego prospect. The magmatic sulfide mineralization at Manchego is hosted by a range of gabbronoritic rock types situated below a linear magnetic anomaly interpreted to be a magnetite layer belonging to the layered mafic-ultramafic Jameson Range intrusion, which predates the Manchego intrusion. The principal ore minerals comprise massive to disseminated pyrrhotite, chalcopyrite, pentlandite, magnetite, and ilmenite. The presence of several geochemically distinct gabbronoritic lithotypes and an abundance of xenoliths strongly indicate a dynamic magmatic plumbing system, such as a conduit-type environment. Whole-rock samples of sulfide-rich gabbronoritic lithologies have δ34S values ranging from -11.8 to -8.4%, which clearly demonstrates the addition of crustal sulfur at Manchego and therefore the availability of crustal sulfur in the West Musgrave province. In comparison to Nebo-Babel, the lithologies intersected at Manchego geochemically resemble the high Ti basaltic NB-4 dikes described by Godel et al. (2011), which are compositionally distinct from the proposed parental magma for the Nebo-Babel intrusion. Therefore, the Manchego prospect provides evidence for the prospectivity of intrusions derived from high Ti basalts in the area, such as the Alcurra Dolerite. Manchego shares many genetic similarities with the Pants Lake intrusion in northern Labrador; both are situated in a magma conduit-type system and assimilated crustal sulfur. However, neither intrusion was sufficiently dynamic to allow the emplacement of chalcophile-undepleted magma pulses, which could have led to an upgrading of metals. Based on present knowledge, this very important step in the formation of economic sulfide deposits is seemingly missing at Manchego; however, exploration is at an early stage.
Keywords: Natural resources exploration; Nickel; Western Australia; layered intrusions; platinum group elements
-
Economic Geology 110(2015)8, 2063-2085
DOI: 10.2113/econgeo.110.8.2063
Cited 9 times in Scopus
Permalink: https://www.hzdr.de/publications/Publ-22925
Heavy ions at the DREAMS facility
Pavetich, S.; Fifield, K.; Fröhlich, M.; Hotchkis, M.; Merchel, S.; Rugel, G.; Wallner, A.; Ziegenrücker, R.
Abstract
The Dresden Accelerator Mass Spectrometry (DREAMS) facility is designed for the measurement of 10Be, 26Al, 36Cl, 41Ca and 129I [1]. The actual goal is to extend the measurement capabilities to actinides. For this purpose, a time-of-flight system was designed and is currently under construction. The system is based on a 1.5 m long flight path and thin carbon foils with Micro Channel Plates as start and stop detectors. For an optimal tuning of the system with low currents, special beam diagnostic elements are planned. In order to characterize the existing system, first measurements of actinide samples have been performed in collaboration with the ANU and ANSTO, using an ionization chamber as detector. Measurements of Pu-isotopes in the 3+ and the 5+ charge state have been conducted.
[1] S. Akhmadaliev et al., NIMB 294 (2013) 5.
Keywords: AMS; actinides; time-of-flight
Involved research facilities
- Ion Beam Center DOI: 10.17815/jlsrf-3-159
Related publications
- DOI: 10.17815/jlsrf-3-159 is cited by this (Id 22924) publication
-
Poster
DPG-Frühjahrstagung der Sektion AMOP (SAMOP), 23.-27.03.2015, Heidelberg, Deutschland
Permalink: https://www.hzdr.de/publications/Publ-22924
Determination of the Maxwellian averaged cross-section of the reaction 35Cl(n,γ)36Cl
Pavetich, S.; Akhmadaliev, S.; Dillmann, I.; Halfon, S.; Heftrich, T.; Käppeler, F.; Lederer, C.; Martschini, M.; Merchel, S.; Paul, M.; Reifarth, R.; Rugel, G.; Steier, P.; Tessler, M.; Wallner, A.; Weigand, M.; Weissman, L.
Abstract
Routine measurements of 36Cl at the Dresden Accelerator Mass Spectrometry (DREAMS) facility have resulted in an astrophysical application: the determination of the Maxwellian averaged cross-section (MACS) of the reaction 35Cl(n,γ)36Cl. As 35Cl acts as a neutron poison in the nucleosynthesis processes during later burning phases of stars, the reaction is important for astrophysical calculations of elemental abundances. The neutron irradiations with a quasi Maxwell Boltzmann spectrum for the production of 36Cl were performed at the Karlsruhe Institute of Technology and the Soreq Applied Research Accelerator Facility. AMS measurements were performed at VERA and DREAMS and are planned at the Australian National University in 2015. Acknowledgement: Alberto Mengoni, CERN.
Keywords: Accelerator Mass Spectrometry; DREAMS; astrophysics; 36Cl
Involved research facilities
- Ion Beam Center DOI: 10.17815/jlsrf-3-159
Related publications
- DOI: 10.17815/jlsrf-3-159 is cited by this (Id 22923) publication
-
Lecture (Conference)
DPG-Frühjahrstagung der Sektion AMOP (SAMOP), 23.-27.03.2015, Heidelberg, Deutschland
Permalink: https://www.hzdr.de/publications/Publ-22923
A study of two-phase flow in monoliths using ultrafast single-slice X-ray computed tomography
Schäfer, T.; Meitzner, C.; Lange, R.; Hampel, U.
Abstract
Running chemical reactions in monolithic structures is being considered as highly promising for intensifying industrial reaction processes. A potential pitfall of such structures is the difficulty to achieve homogeneous and well defined gas/liquid distributions patterns with economically feasible distribution mechanisms. Experimental studies on gas/liquid distribution in monoliths are often hampered by missing measurement and visualization technique to disclose the two-phase flow inside the narrow and opaque channels.
This paper presents results of a study carried out with ultrafast single-slice X-ray tomography, a novel imaging techniques , which can overcome these limitations. We investigated two-phase flow in two different types of square-channel monolith structures, one with high cell density of 400 cpsi and one with low cell density of 39 cpsi. Our study discloses in-channel flooding and draining behavior via extraction of characteristic distribution parameters, such as averaged and channel-linked liquid holdup, two-phase flow patterns and liquid maldistribution from X-ray images using advanced image processing techniques.
Keywords: ultrafast X-ray tomography; two-phase flow; monolith; holdup; maldistribution; flow pattern; flow visualization
Involved research facilities
- TOPFLOW Facility
-
International Journal of Multiphase Flow 86(2016), 56-65
DOI: 10.1016/j.ijmultiphaseflow.2016.07.008
Cited 6 times in Scopus
Permalink: https://www.hzdr.de/publications/Publ-22922
Image reconstruction for hard field tomography
Hampel, U.
Abstract
Computed tomography requires the solution of an inverse problem, that is, the reconstruction of an object distribution from measurement data. In hard field tomography this problem can be more specifically referred to as the reconstruction of an object distribution from its line integrals. A first solution to the mathematical problem was given by Johann Radon in 1917 long before anyone thought about computed tomography. The transformation of an object distribution into the space of its line integrals is hence today called the Radon transformation. With the development of computed tomography technology later quite powerful algorithms basing on analytic and algebraic inversion schemes for the Radon transform were developed. This chapter shall introduce the mathematical fundamentals of the forward and inverse problem of hard field computed tomography, the discretization of the problem and further discuss some distinct features and specialties of image reconstruction, such as 3D inversion approaches and concepts for limited and local tomography.
Keywords: Image reconstruction; Radon transformation; inverse problem; analytic reconstruction; algebraic reconstruction; cone-beam reconstruction; limited data tomography
Involved research facilities
- TOPFLOW Facility
-
Book chapter
Mi Wang: Industrial Tomography: Systems and Applications, Amsterdam: Woodhead Publishing, 2015, 1782421181, 347-376
Permalink: https://www.hzdr.de/publications/Publ-22921
Actinide AMS at DREAMS
B. Khojasteh, N.; Merchel, S.; Pavetich, S.; Rugel, G.; Scharf, A.; Ziegenrücker, R.
Abstract
Radionuclides such as 236U and 239Pu were introduced into the environment by atmospheric nuclear weapon tests, reactor accidents (Chernobyl, Fukushima), releases from nuclear reprocessing facilities (Sellafield, La Hague), radioactive waste disposal, and accidents with nuclear devices (Palomares, Thule) [1]. Accelerator Mass Spectrometry (AMS) is the most sensitive method to measure these actinides.
The DREsden AMS (DREAMS) facility is located at a 6 MV accelerator, which is shared with ion beam analytics and implantation users, preventing major modifications of the accelerator and magnetic analyzers. DREAMS was originally designed for 10Be, 26Al, 36Cl, 41Ca, and 129I [2,3]. To modify the system for actinide AMS, a Time-of-Flight (TOF) beamline at the high-energy side has been installed and performance tests are on-going. Ion beam and detector simulations are performed to design a moveable ionization chamber. Especially, the detector window and anode dimensions have to be optimized. This ionization chamber will act as an energy detector of the system and its installation is planned as closely as possible to the stop detector of the TOF beamline for highest detection efficiency.
[1] Srncik et al., J. Environ. Radioact. 132 (2014) 108. [2] Akhmadaliev et al., Nucl. Instr. Meth. B. 294 (2013) 5. [3] Rugel et al., under review in Nucl. Instr. Meth. B.
Keywords: AMS; DREAMS; actinides; ionization chamber
Involved research facilities
- Ion Beam Center DOI: 10.17815/jlsrf-3-159
Related publications
- DOI: 10.17815/jlsrf-3-159 is cited by this (Id 22920) publication
-
Poster
DPG-Frühjahrstagung der Sektion AMOP (SAMOP), 29.02.-04.03.2016, Hannover, Deutschland
Permalink: https://www.hzdr.de/publications/Publ-22920
X-ray computed tomography
Hampel, U.
Abstract
Computed tomography with X-rays is widely used in medicine and non-destructive testing today. In process applications X-ray tomography is, however, until now more seldom used, which is obviously due to its high complexity and costs. Nonetheless, particularly in laboratory studies it has frequently proven its superior capability to measure multiphase flow parameters, such as local phase fractions in pipes, vessels or other process system components, with high resolution and accuracy. Most recently different technologies were presented, which allow faster tomographic imaging of flows with X-ray CT, which now opens the door for a wider application of this technique in process analysis, monitoring and control. The chapter gives a concise overview over basic principles and hardware of X-ray CT with particular respect to process applications and provides state-of-the-art examples of its application in multiphase flow analysis.
Keywords: X-ray tomography
Involved research facilities
- TOPFLOW Facility
-
Book chapter
Mi Wang: Industrial Tomography: Systems and Applications, Amsterdam: Woodhead Publishing, 2015, 1782421181, 175-196
Permalink: https://www.hzdr.de/publications/Publ-22919
Funktionelle Charakterisierung der Wechselwirkungen zwischen neuartigen polymeren Biomaterialien und dem Organismus
Ullm, S.
Abstract
Die funktionelle Wiederherstellung geschädigter Zellen, Gewebe oder Organe ist das Hauptziel der regenerativen Medizin. Der Einsatz innovativer Biomaterialien, die mit dem Organismus positiv interagieren, gilt als besonders aussichtsreicher Ansatz zur Realisierung dieses Ziels. Aus diesem Grund sind die Entwicklung neuartiger Biomaterialkonzepte und die Verbesserung des Verständnisses der Wechselwirkungen zwischen Biomaterial und Organismus Kernthemen der aktuellen Biomaterialforschung.
Die vorliegende Arbeit wurde im Kontex des von der Helmholtz-Gemeinschaft geförderten Portfoliothemas "Technologie und Medizin - Multimodale Bildgebung zur Aufklärung des in-vivo-Verhaltens von polymeren Biomaterialien" angefertigt. Die Aufgabe der beteiligten Helmholtz-Zentren und Universitäten besteht in der Entwicklung und Optimierung multiskaliger und multimodaler Bildgebungsverfahren zur Untersuchung des Verhaltens polymerer Biomaterialien im Körper. Das Hauptaugenmerk soll dabei auf der Aufklärung der auftretenden Wechelwirkungen zwischen Biomaterial und Organismus sowie der Identifizierung der Abbauprodukte des jeweiligen Biomaterials liegen, mit dem Ziel, dessen in-vivo-Verhalten besser vorhersagen zu können und so die Entwicklungszeiten erheblich zu verkürzen.
Gegenstand der vorliegenden Arbeit war es, eine Gruppe vielversprechender polymerer Biomaterialien auf der Basis von Gelantine hinsichtlich ihrer Wechselwirkungen mit ausgewählten Zelltypen und dem gesamten Organismus eingehend zu charakterisieren. Die zu untersuchenden Gelantine-basierten Hydrogele wurden im Rahmen des oben genannten Helmholtz-Portfoliothemas von der Arbeitsgruppe um Dr. Axel Neffe am Helmholtz-Zentrum Geesthacht, Institut für Biomaterialforschung Teltow, synthetisiert sowie hinsichtlich ihrer Materialeigenschaften charakterisiert und ersten in-vitro-Experimenten mit murinen Fibroblasten und mesenchymalen Stammzellen eingesetzt. In der vorliegenden Arbeit sollte die Reaktion verschiedener humaner Zellsysteme, die Schlüsselrollen während der Gewebereaktion und Neovaskularisierung einnehmen, auf die Hydrogele und deren Abbauprodukte untersucht werden. Darüber hinaus sollte das In-vivo-Verhalten der Hydrogele in einem subkutanen Implantationsmodell in immunkompetenen Mäusen analysiert werden. Im Ergebnis sollte die vorliegende Dissertation einerseits dazu beitragen das Anwendungspotential der untersuchten Hydrogele zu beurteilen und andererseits das allgemeine Verständnis der Biomaterial-Gewebe-Interaktion zu erweitern.
Involved research facilities
- PET-Center
-
Doctoral thesis
TU Dresden, 2015
Mentor: Prof. Jens Pietzsch
155 Seiten
Permalink: https://www.hzdr.de/publications/Publ-22918
Analysis of intermittent flow patterns of water-steam flow in solar thermal power plants with direct steam generation
Hoffmann, A.; Hirsch, T.; Schleicher, E.; Pitz-Paal, R.
Abstract
Solar thermal power plants that use parabolic troughs for direct steam generation depict a commercially available technology for a renewable electricity production. The once-through operation mode is the most cost-effective approach for this type of power plant and, consequently, is mainly considered in the current research. This operation mode preheats and evaporates water and superheats steam within one continuous pipe. Hence, all mass qualities are passed along the pipe and various flow patterns are present. It is presumed that intermittent flow pattern influence the position of the mixture-vapor transition point at the end of evaporation and lead to undesired thermal stresses in the receiver pipe. In order to get an insight in the two-phase flow a numerical analysis is performed with ATHLET. This code provides a one-dimensional mass, momentum and energy balance for both phases water and steam, respectively. The applicability of ATHLET on intermittent flows is discussed and confirmed. In the result an intermittent flow is numerically determined at specific void fraction ranges in the design of the DISS test facility at the Plataforma Solar de Almería, Spain. The occurrence of these unsteady flow pattern diminishes at a pressure P > 60 bar. Furthermore, it is shown that the oscillating nature of the two-phase flow effects the position of the mixture-vapor transition point. For the validation of the numerical results an experiment with a wire-mesh sensor is designed. The obtained results deliver a substantial contribution to understand the two-phase flow behavior in the direct steam generation process.
Keywords: Direct steam generation; ATHLET; flow pattern
-
Contribution to proceedings
ICMF-2016 - 9th International Conference on Multiphase Flow, 22.-27.05.2016, Firenze, Italy -
Lecture (Conference)
ICMF-2016 - 9th International Conference on Multiphase Flow, 22.-27.05.2016, Firenze, Italy
Permalink: https://www.hzdr.de/publications/Publ-22916
The HZDR reactor dynamics code DYN3D
Kliem, S.
Abstract
The presentation gives an overview on the code DYN3D which is a three-dimensional core model for steady-state, dynamic and depletion calculations in reactor cores with quadratic or hexagonal fuel assembly geometry being developed by the Helmholtz-Zentrum Dresden-Rossendorf for more than 20 years. An overview on the basic DYN3D models and the available code couplings is given. The verification and validation status is shortly outlined.
-
Invited lecture (Conferences)
1st Sino-German Symposium on Fundamentals of Advanced Nuclear Safety Technology, 09.-12.03.2015, Shanghai, China
Permalink: https://www.hzdr.de/publications/Publ-22915
Synthese und kinetische Charakterisierung von Endopeptidase-Substraten des Cathepsin B
Behring, L.
Abstract
Das Leben sämtlicher Orgnismen beruht auf einem vielschichtigen, feinabgestimmten System enzymatischer Reaktionen, die ein komplexes Regulationssystem erfordern. Da sich die meisten Erkrankungen auf Fehlfunktionen verschiedener Enzyme zurückführen lassen, ist es ein wichtiges Anliegen der Forschung, diese enzymatischen Prozesse zu verstehen und beeinflussen zu lernen.
Aufgrund des engen Zusammenspiels verschiedener Prozesse ist für das Verständnis der Rolle unterschiedlicher Enzyme an Krankheitsbildern wie Krebs die Beobachtung der in vivo stattfindenden Reaktionen nötig. Dafür stehen verschiedene Bildgebungsverfahren zur Verfügung. Besonders geeignet sind hierbei PET (Positronenemissionstomographie) und SPECT (single photon emission computed tomography). Beide Verfahren sind nichtinvasiv, beeinflussen den untersuchten Organismus minimal und können mit hoher Sensitivität funktionelle Informationen geben.
Die Suche nach geeigneten Targeting-Strategien und die Entwicklung problemspezifischer Tracer sind daher wichtige Schritte auf dem Weg zu einem besseren Verständnis der Prozesse, die verschiedenen Krankheitsbildern zugrunde liegen und damit auch auf dem Weg zur Heilung dieser Erkrankungen.
Involved research facilities
- PET-Center
-
Master thesis
TU Dresden, 2015
Mentor: Prof. Jens Pietzsch
169 Seiten
Permalink: https://www.hzdr.de/publications/Publ-22914
Challenges and Solutions on the Major and Trace Element Analysis of Eudialyte Group Minerals with the Electron Microprobe
Krause, J.; Atanasova, P.; Möckel, R.; Osbahr, I.; Rudolph, M.; Gutzmer, J.
Abstract
Alkaline complexes containing eudialyte group minerals (EGM) comprise one of the most promising sources for future rare earth element (REE) supply. The accurate quantification of the chemical composition of EGM is complicated by both mineralogical and X-ray-specific challenges. These include:
1) structural and chemical variability of EGM composition (e.g., [1-3]);
2) mutual interferences of X-ray lines from major and trace elements, in particular REEs [4];
3) the diffusive volatility of light anions as F and Cl and cations such as K and Na;
4) particular instability of EGM under the electron beam.
A novel analytical approach has been developed to account for the above-mentioned analytical challenges. Additionally, loss on ignition and differential scanning calorimetry data has been applied to constrain the content and composition of volatiles in the EGM structure. The influence of the electron beam on the structure of EGM has been explored with Raman spectroscopy. All correction for the overlapping of X-ray lines is processed offline. For comparison a subset of samples was analysed with Laser Ablation Inductively Coupled Plasma Mass Spectrometry. The results demonstrate that the abovementioned parameters need to be considered and carefully optimized to perform accurate quantitative analyses on the chemical composition of EGM with the electron microprobe.
-
Contribution to proceedings
Goldschmidt 2015, 16.-21.08.2015, Prag, Tschechische Republik
Goldschmidt2015 Abstracts: Cambridge Publications, 1688-1688 -
Poster
Goldschmidt 2015, 16.-21.08.2015, Prag, Tschechische Republik
Permalink: https://www.hzdr.de/publications/Publ-22913
Petrographie der SEE-Th-Gänge von Lehmi Pass in Idaho und Montana
Hüttel, S. P.
Abstract
Diese Bachelorarbeit befasst sich mit der Petrographie den Seltenerdelement-Thorium-Gängen von Lemhi Pass in Idaho und Montana. Im Rahmen des Projektes sollen die Seltenerdgehalte der Gänge, über die bisher nur wenig bekannt ist, untersucht und eine Wertung der Seltenerdelement-Gehalte gegeben werden.
-
Bachelor thesis
TU Bergakademie Freiberg, 2015
Mentor: Bernhard Schulz, Petya Atanasova
90 Seiten
Permalink: https://www.hzdr.de/publications/Publ-22912
Petrographie der SEE-Karbonate von Sheep Creek in Ravalli County, Montana
Meumann, J.
Abstract
Bei den metamorphen Karbonaten von Sheep Creek, Montana handelt es sich ursprünglich entweder um flachmarine Sedimentite oder kabonatitische Gänge. Diese wurden durch LREE-reiche (light rare earth elements), metamorph mobilisierte Wässer wenigstens partiell vererzt. Sie stehen als linsen- bis bandförmige Strukturen mit maximal 2,40 m Mächtigkeit in Wechsellagerung mit Amphiboliten an. Diese Abfolge ist wiederum in 2,7 Ga alten und somit neoarchaischen Gneisen eingeschaltet. Die bearbeiteten Proben konnten wie folgt gruppiert werden: In Allanit-Monazit-Calcit-, allanitreiche Karbonat-Silikat-, Ankerit-Magnetit-Ilmenit-, Ankerit-Calcit-Ferrosilit-, Enstatit-Calcit- und massive Ilmenit-Magnetit-Gesteine.
Als wesentliche SEE-Minerale sind in den Marmoren Monazit und Allanit vertreten. Es sind allerdings auch andere potentiell ökonomisch relevante Minerale in Form von Ilmenit, Magnetit, Titanit, Apatit und Baryt partiell angereichert. Monazit und Allanit machen insgesamt stellenweise mehr als 80 wt-% der Gesteine aus, wobei hauptsächlich leichte Elemente angereichert sind. In den Monaziten sind 11 wt-% bis 53 wt-% an leichten SEE in Form von Cer, Lanthan und Neodym eingebaut.
Bei den Allaniten fallen die Gehalte mit insgesamt 11 wt-% bis 26 wt-% Cer, Lanthan und Neodym geringer aus. Eine Verwachsung mit radioaktiven Mineralen wie z. B. Thorit ist hier praktisch bedeutungslos.
In einer Probe sind Ilmenitgehalte von ~ 66 wt-% anzutreffen, Magnetit ist dagegen mit Massenanteilen von stets weniger als 10 wt-% nur untergeordnet anzutreffen. Selbiges gilt für Titanit mit maximal ~ 2,5 wt-% und für Apatit mit generell < 5 wt-%. Baryt ist dafür stellenweise mit bis zu ~ 17 wt-% angereichert.
-
Bachelor thesis
TU Bergakademie Freiberg, 2015
Mentor: Bernhard Schulz, Petya Atanasova
109 Seiten
Permalink: https://www.hzdr.de/publications/Publ-22911
Euler-Euler Modeling of Poly-Dispersed Bubbly Flows
Rzehak, R.
Abstract
CFD simulations of bubbly flow on the scale of technical equipment become feasible within the Eulerian two-fluid framework of interpenetrating continua. For practical applications suitable closure relations are required which describe the interfacial exchange processes. To facilitate predictive simulations a reference set of closure relations has been defined for bubble forces and bubble-induced turbulence including numerical values for all parameters. Models for bubble coalescence and breakup are not yet included at present due to their lacking maturity. This means that the bubble size distribution must still be estimated by other means or treated as a parameter in a sensitivity study. Using measured bubbles sizes the validity of model predictions for gas fraction, mean velocities of gas and liquid, and liquid turbulent kinetic energy have been validated over a range of conditions. These include both pipe flows and bubble columns and circular and rectangular cross sections. The bubble size is limited to the range of 1 to 10 mm and the gas fraction to at most 10 to 20 %. The present report gives a brief but complete description of the model, a few validation examples, and references for further study.
Keywords: fluid dynamics; dispersed gas liquid multiphase flow; Euler-Euler two-fluid model; closure relations; CFD simulation; model validation
-
Book chapter
Guan Heng Yeoh: Handbook of Multiphase Flow Science and Technology, Singapore: Springer, 2017, 978-981-4585-86-6
DOI: 10.1007/978-981-4585-86-6_4-1
Permalink: https://www.hzdr.de/publications/Publ-22910
The formation of silver metal nanoparticles by ion implantation in silicate glasses
Vytykacova, S.; Svecova, B.; Nekvindova, P.; Spirkova, J.; Mackova, A.; Miksova, R.; Böttger, R.
Abstract
It has been shown that glasses containing silver metal nanoparticles are promising photonics materials for the fabrication of all-optical components. The resulting optical properties of the nanocomposite glasses depend on the composition and structure of the glass, as well as on the type of metal ion implanted and the experimental procedures involved. The main aim of this article was to study the influence of the conditions of the ion implantation and the composition of the glass on the formation of metal nanoparticles in such glasses.
Four various types of silicate glasses were implanted with Ag+ ions with different energy (330 keV, 1.2 MeV and 1.7 MeV), with the fluence being kept constant (1 × 1016 ions cm−2). The as-implanted samples were annealed at 600 °C for 1 h. The samples were characterised in terms of: the nucleation of metal nanoparticles (linear optical absorption), the migration of silver through the glass matrix during the implantation and post-implantation annealing (Rutherford backscattering spectroscopy), and the oxidation state of silver (photoluminescence in the visible region).
Keywords: Silicate glasses; Silver nanoparticles; Ion implantation
Involved research facilities
- Ion Beam Center DOI: 10.17815/jlsrf-3-159
Related publications
- DOI: 10.17815/jlsrf-3-159 is cited by this (Id 22909) publication
-
Nuclear Instruments and Methods in Physics Research B 371(2016), 245-250
Online First (2015) DOI: 10.1016/j.nimb.2015.10.016
Cited 13 times in Scopus
Permalink: https://www.hzdr.de/publications/Publ-22909
The structural and optical properties of metal ion-implanted GaN
Macková, A.; Malinský, P.; Sofer, Z.; Šimek, P.; Sedmidubský, D.; Veselý, M.; Böttger, R.
Abstract
The practical development of novel optoelectronic materials with appropriate optical properties is strongly connected to the structural properties of the prepared doped structures. We present GaN layers oriented along the (0 0 0 1) crystallographic direction that have been grown by low-pressure metal–organic vapour-phase epitaxy (MOVPE) on sapphire substrates implanted with 200 keV Co+, Fe+ and Ni+ ions. The structural properties of the ion-implanted layers have been characterised by RBS-channelling and Raman spectroscopy to obtain a comprehensive insight into the structural modification of implanted GaN layers and to study the subsequent influence of annealing on crystalline-matrix recovery. Photoluminescence was measured to control the desired optical properties. The post-implantation annealing induced the structural recovery of the modified GaN layer depending on the introduced disorder level, e.g. depending on the ion implantation fluence, which was followed by structural characterisation and by the study of the surface morphology by AFM.
Keywords: RBS channelling; Metal-implanted GaN; Structural changes
Involved research facilities
- Ion Beam Center DOI: 10.17815/jlsrf-3-159
Related publications
- DOI: 10.17815/jlsrf-3-159 is cited by this (Id 22908) publication
-
Nuclear Instruments and Methods in Physics Research B 371(2016), 254-257
Online First (2015) DOI: 10.1016/j.nimb.2015.10.015
Cited 6 times in Scopus
Permalink: https://www.hzdr.de/publications/Publ-22908
Ultrafast nonlinear response of GaAs under high pressures
Braun, J. M.; Schneider, H.; Helm, M.; Pashkin, A.
Abstract
Applying hydrostatic pressure leads to dramatic changes in the band structure of semiconductors. In particular, it enables a continuous tuning of the bandgap energy of a given sample. Here we study ultrafast carrier dynamics in gallium arsenide (GaAs) at pressures up to 3 GPa. The optical pump-probe spectroscopy traces the nonlinear response in the vicinity of the bandgap. Thus, we are able to observe the changes in the ultrafast response caused by tuning the bandgap energy across the spectrum of the femtosecond probe pulse.
Our setup employs a femtosecond Ti:sapphire laser which provides pulses with the spectrum centered around 1.55 eV and a FWHM of ~0.1 eV. The experiment is performed in a non-collinear reflection geometry (fig. 1) where the pump and probe beams are focused by an all-reflective Schwarzschild objective to a ~5μm spot on the sample. Pressure is applied in a diamond anvil cell (DAC) with CsI used as pressure transmitting medium in order to ensure a good contact between the sample and diamond anvil. The sample studied is a semi-insulating GaAs crystal with thickness of about 50μm. The pump pulse with energy of 0.03 nJ induces changes in the optical reflectivity of the sample which is probed by the delayed weaker probe pulse.
In agreement with a previous study at ambient and low pressures, pumping induces an increase in reflectivity which decays on a timescale of hundred picoseconds and is assigned to the recombination of the photogenerated charge carriers [1]. With pressure increase, this relaxation becomes slower as shown in fig. 2. Finally, for pressures above 2 GPa, the pump-probe signal changes its sign and the relaxation components vanish completely. The nonlinear response appears only around zero pump-probe delay and probably originates from the negative real part of the thirdorder susceptibility of GaAs [2]. We interpret this phenomenon as a shifting of the bandgap energy above the excitation spectrum of our experiment. This assumption is in good agreement with the known bandgap pressure coefficient of 0.11 eV/GPa in GaAs leading to a complete transparency of the sample for pump and probe pulses at pressures above 2 GPa [3].
[1] D. G. McLean, M. G. Roe, A. I. D’Souza, P. E. Wigen, Appl. Phys. Lett. 48, 992 (1986).
[2] A. A. Said, M. Sheik-Bahae, D. J. Hagan, T. H. Wei, J. Wang, J. Young, E. W. Van Stryland, J. Opt. Soc. Am. B 9, 405 (1992).
[3] A. R. Goñi, K. Strössner, K. Syassen, M. Cardona, Phys. Rev. B 36, 1581 (1987).
Keywords: pump-probe spectroscopy; recombination dynamics; high pressure; diamond anvil cell; gallium arsenide; GaAs
-
Poster
Joint AIRAPT-25th & EHPRG-53rd International Conference on High Pressure Science and Technology, 30.08.-04.09.2015, Madrid, Spain
Permalink: https://www.hzdr.de/publications/Publ-22907
Ultrafast nonlinear response of GaAs under high pressures
Braun, J. M.; Schneider, H.; Helm, M.; Pashkin, A.
Abstract
Applying hydrostatic pressure leads to dramatic changes in the band structure of semiconductors. In particular, it enables continuous tuning of the bandgap energy. Thus, optical pump-probe spectroscopy under high pressures allows the study of nonlinear optical response in the vicinity of the interband resonance.
Here, we study ultrafast carrier dynamics in gallium arsenide (GaAs) at pressures up to 3 GPa. Our setup employs a femtosecond Ti:sapphire laser which provides pulses with the spectrum centered around 1.55 eV with a FWHM of ~0.1 eV. The experiment is performed in a non-collinear reflection geometry (fig. 1) where the pump and probe beams are focused by an all-reflective Schwarzschild objective to a ~5µm spot on the sample. Pressure is applied in a diamond anvil cell with CsI used as pressure transmitting medium. The studied sample is a semi-insulating GaAs crystal with thickness of about 50µm. The pump pulse with energy of 0.03 nJ induces changes in the optical reflectivity of the sample which is probed by the delayed weaker probe pulse.
In agreement with a previous study at ambient pressure, pumping induces an increase in reflectivity which decays on a timescale of hundred picoseconds and is assigned to the recombination of the photogenerated charge carriers [1]. With increasing pressure this relaxation becomes slower as demonstrated in fig. 2. Finally, for pressures above 2 GPa, the pump-probe signal changes its sign and the relaxation component vanishes completely. The nonlinear response appears only around zero pump-probe delay and its origin is attributed to the negative real part of the third-order susceptibility of GaAs [2]. We interpret this phenomenon as a shifting of the bandgap energy above the excitation spectrum of our experiment. This assignment is in good consistency with the known bandgap pressure coefficient of 0.11 eV/GPa in GaAs leading to a complete transparency of the sample for pump and probe pulses at pressures above 2 GPa [3].
In the future we plan to study the response of the photoexcited electron-hole plasma in GaAs using optical pump / THz probe spectroscopy under pressure. The all-reflective optics of our experimental setup enables us to couple coherent THz radiation pulses from the free-electron laser at the HZDR into a diamond anvil cell.
[1] D. G. McLean, M. G. Roe, A. I. D’Souza, P. E. Wigen, Appl. Phys. Lett. 48, 992 (1986).
[2] A. A. Said, M. Sheik-Bahae, D. J. Hagan, T. H. Wei, J. Wang, J. Young, E. W. Van Stryland, J. Opt. Soc. Am. B 9, 405 (1992).
[3] A. R. Goñi, K. Strössner, K. Syassen, M. Cardona, Phys. Rev. B 36, 1581 (1987).
Keywords: pump-probe spectroscopy; recombination dynamics; high pressure; diamond anvil cell; gallium arsenide; GaAs
-
Poster
German THz Conference 2015, 08.-10.06.2015, Dresden, Deutschland
Permalink: https://www.hzdr.de/publications/Publ-22906
Gouy phase shift of a tightly focused, radially polarized beam
Kaltenecker, K. J.; König-Otto, J. C.; Mittendorff, M.; Winnerl, S.; Schneider, H.; Helm, M.; Helm, H.; Walther, M.; Fischer, B. M.
Abstract
Radially polarized beams represent an important member of the family of vector beams, in particular due to the possibility of using them to create strong and tightly focused longitudinal fields, a fundamental property that has been exploited by applications ranging from microscopy to particle acceleration. Since the properties of such a focused beam are intimately related to the Gouy phase shift, proper knowledge of its behavior is crucial. Terahertz microscopic imaging is used to extract the Gouy phase shift of the transverse and longitudinal field components of a tightly focused, radially polarized beam. Since the applied terahertz time-domain approach is capable of mapping the amplitude and phase of an electromagnetic wave in space, we are able to directly trace the evolution of the geometric phase as the wave propagates through the focus. We observe a Gouy phase shift of 2π for the transverse and of π for the longitudinal component. Our experimental procedure is universal and may be applied to determine the geometric phase of other vector beams, such as optical vortices, or even arbitrarily shaped and polarized propagating waves.
Keywords: Gouy phase; EOS; THz
-
Optica 3(2016)1, 35-41
DOI: 10.1364/OPTICA.3.000035
Cited 36 times in Scopus
Permalink: https://www.hzdr.de/publications/Publ-22905
Metallurgical infrastructure: a key enabler of a circular economy
Reuter, M. A.
Abstract
Base metals such as copper, lead, nickel, cobalt, zinc etc. form the basic crucial carrier metals for a sustainable society – the Web of Metals. This paper discusses the special and crucial role these metals have in acting as enablers in any recycling efforts as they carry and release important and vital minor elements at the heart of high-tech applications and products. Through examination of the rising needs for such carriers, this paper examines the approach and technologies which need to be considered by any producer of base metals. Attention is paid to the limits and extent of this carrier role in the typical processing of materials.
Examples of specialised technology and flowsheet needs are presented with consideration given to a “whole of chain” or Systems-Integrated Metal Production (SIMP) approach as a cornerstone of a circular economy. Also outlined are the challenges facing not only producers, but legislators who need to consider the balance between providing our societal needs with baseline technology infrastructure requirements for valuable metals extraction. In summary, the message of this paper states simply that not only is the criticality of metals important but the criticality of the infrastructure (Infrastructure Criticality) that can recover metals from complex designed “mineral” mixtures. Base metals are at the heart of a Circular Economy, therefore key enablers of the Internet-of-Metallurgical-Things.
Keywords: Resource efficiency base metals; Recycling; System integration; Design for Recycling (DfR)
-
Invited lecture (Conferences)
On metal by-products recovery, 12.-13.11.2015, Brüssel, Belgien -
Invited lecture (Conferences)
Cleantech Innovations in Mineral Production, 10.09.2015, Helsinki, Finland
Permalink: https://www.hzdr.de/publications/Publ-22904
Kreislaufwirtschaft 4.0
Reuter, M. A.
Abstract
Kreislaufwirtschaft 4.0
-
Invited lecture (Conferences)
UBA-Workshop „Rückgewinnung von Edel- und Sondermetallen“, 02.11.2015, Berlin, Deutschland
Permalink: https://www.hzdr.de/publications/Publ-22903
Application of CFD towards the thermal-hydraulic analysis of Spent Fuel Pool accidents
Oertel, R.; Krepper, E.; Lucas, D.
Abstract
After a spent fuel assembly is removed from the reactor core, its decay heat production is still too large for pure conductive cooling. It is placed in a Spent Fuel Pool, where the decay heat is removed from the assembly by means of natural convection, while the pool cooling system keeps the water temperature at about 40-50°C. The fuel assemblies are typically arranged in high density racks which consist of borated steel in order to prevent criticality accidents. The rack cells are closed to the sides and force the coolant flow along the axial direction. In the event of a failure of the cooling system followed by boil-off, the water level might decrease below the top of the assemblies. Then the natural circulation path in the water phase is blocked and the dominant cooling mechanisms for the uncovered section of the fuel assemblies are the forced convection due to steam production and the solid heat conduction into the remaining water, as well as towards the upper end. The latter mechanism depends on the boundary conditions at the fuel assembly head, which are determined by the temperature and velocity field in the pool and reactor building atmosphere. Additionally, if the decay heat load of the neighboring fuel assemblies differs significantly, some heat will be exchanged in the radial direction. In the nuclear community, system codes are widely used for safety studies. They deliver fast and reliable results for the flow and heat transfer inside the fuel assemblies. But since three-dimensional convective phenomena can only be taken into account in the form of simplified assumptions, they do not entirely qualify for studies related to Spent Fuel Pools. In this work, CFD is used to study the flow field above and around the exposed storage racks in order to identify large scale convective phenomena. It is expected that the large scale flow field is dictated by the temperature field in the pool, which in turn influences the cooling of the individual fuel assemblies. These interdependencies need to be quantified as a function of the storage rack arrangement and the overall distribution of the fuel assemblies with respect to their decay heat. A porous body approach is employed for the modeling of the fuel assemblies. Best Practice Guidelines are applied as far as possible, since there is no experimental data available that allows a straightforward validation of the simulation results. In this work, the Spent Fuel Pool design of Fukushima's Unit 4 serves as a test case. A loss of coolant by boil-off is postulated, leading to partially uncovered fuel assemblies. Several pool loading strategies for a constant total decay heat load will be presented and conclusions will be drawn as to which configuration is the most favorable from a thermohydraulic standpoint.
Keywords: Spent Fuel Pool safety; loading strategies; CFD; convective heat transfer
-
Lecture (others)
10. Doktorandenseminar des Kompetenzverbundes für Kerntechnik Ost, 08.12.2015, Dresden, Deutschland
Permalink: https://www.hzdr.de/publications/Publ-22902
Investigations on the anisotropy of charge carrier excitation in graphene with low energetic photons
Otto, J.; Mittendorff, M.; Winzer, T.; Malic, E.; Knorr, A.; Schneider, H.; Helm, M.; Winnerl, S.
Abstract
Recently we have demonstrated anisotropic excitation and relaxation of charge carriers in graphene [1]. A near-infrared pump probe experiment with varied angle between pump and probe polarization revealed anisotropic carrier populations on a 100 fs timescale as predicted by microscopic theory. An isotropic distribution is then reached by scattering via optical phonons.
Now we perform an experiment where scattering of electrons with optical phonons is strongly suppressed. To this end a photon energy of 88 meV, i.e. far below the optical phonon energy, is applied and the sample is kept at 20 K. The experiments, where the free-electron laser FELBE was used as a source, revealed an anisotropic charge carrier distribution on timescales of up to 10 ps (cf. Fig. 1). In particular we investigate the dependence of the pump-probe signals on pump fluence. We find that the anisotropy is most pronounced for low fluences and vanishes for fluences in the µJ/cm2 range. These results, complemented by microscopic theory, give clear insights in the role of Coulomb scattering on the carrier dynamics. Due to the predominantly collinear nature of Coulomb scattering, the anisotropy at low fluences is preserved on timescales larger than the ~30 fs timescale of the thermalization due to Coulomb scattering. At high fluences, however, Coulomb scattering efficiently redistributes carriers towards an isotropic distribution.
References
[1] M. Mittendorff, T. Winzer, E. Malic, A. Knorr, C. Berger, W. A. de Heer, H. Schneider, M. Helm and S. Winnerl, Nano Lett., 14, 1504-1507, (2014)
Keywords: graphene; ultrafast dynamics
Involved research facilities
- Radiation Source ELBE DOI: 10.17815/jlsrf-2-58
Related publications
- DOI: 10.17815/jlsrf-2-58 is cited by this (Id 22901) publication
-
Poster
Graphene Week 2015, 22.-26.06.2015, Manchester, UK
Permalink: https://www.hzdr.de/publications/Publ-22901
Anisotropic carrier distribution in optically excited graphene: The role of Coulomb scattering
Otto, J.; Mittendorff, M.; Winzer, T.; Malic, E.; Knorr, A.; Schneider, H.; Helm, M.; Winnerl, S.
Abstract
Anisotropic carrier distribution in optically excited graphene: The role of Coulomb scattering
Keywords: graphene; ultrafast dynamics
Involved research facilities
- Radiation Source ELBE DOI: 10.17815/jlsrf-2-58
Related publications
- DOI: 10.17815/jlsrf-2-58 is cited by this (Id 22900) publication
-
Poster
3. SPP Workshop, 17.-20.05.2015, Kremmen, Deutschland
Permalink: https://www.hzdr.de/publications/Publ-22900
Large Scale CFD Simulations of Spent Fuel Pool Accident Scenarios Using a Porous Body Approach
Oertel, R.; Krepper, E.; Lucas, D.
Abstract
After the accident at the Fukushima Daiichi nuclear power plant, the safety of Spent Fuel Pools moved into the focus of nuclear safety research. For the thermo-hydraulic analysis, system- or severe accident codes are used predomenantly, although simplified assumptions have to be made for the flow paths around the storage racks and inside the reactor building. The present work uses CFD in order to investigate the large scale convective phenomena involved and to examine their influence on the cooling of the individual fuel assemblies. All relevant thermophysical phenomena are discussed together with the corresponding modeling. The Spent Fuel Pool of Fukushima’s Unit 4 with the loading at the time of the accident serves as a test case. The paper gives a first qualitative impression on the emerging flow paths for the scenario of partially as well as fully uncovered fuel assemblies. Finally an outlook is given, how CFD can help to study the safety of Spent Fuel Pools as a standalone tool or by delivering input to one-dimensional codes.
Keywords: Spent Fuel Pool safety; CFD; partially uncovered fuel assemblies; convective heat transfer
-
Contribution to proceedings
46th Annual Meeting on Nuclear Technology (AMNT 2015), 05.-07.05.2015, Berlin, Deutschland -
Lecture (Conference)
46th Annual Meeting on Nuclear Technology (AMNT 2015), 05.-07.05.2015, Berlin, Deutschland
Permalink: https://www.hzdr.de/publications/Publ-22899
Long-lived anisotropic carrier populations in graphene excited by THz pulses
Otto, J.; Mittendorff, M.; Winzer, T.; Malic, E.; Knorr, A.; Schneider, H.; Helm, M.; Winnerl, S.
Abstract
Calculations of non-equilibrium charge carrier distributions excited by polarized light indicate anisotropic occupations in momentum space. For most materials experimental insight in this anisotropy is obscured due to complex valence band structures [1]. Recently we have experimentally verified anisotropic carrier distributions and investigated their relaxation in graphene [2]. A near-infrared pump probe experiment with varying angle between pump and probe polarizations revealed anisotropic carrier populations on a 100 fs timescale as predicted by microscopic theory. An isotropic distribution is then reached by scattering via optical phonons. In graphene the Coulomb scattering, in first approximation, is restricted to collinear scattering along a line of the cone-like band structure and therefore preserves the angular orientation of the distribution.
By shifting the photon energies into the THz range (88 meV) and cooling the sample down to 20K we were now able to observe anisotropic charge carrier distributions with a lifetime as long as several picoseconds. Under these conditions scattering via optical phonons, with energies of about 200meV, is strongly suppressed. Note that the observed distribution has a very unusual character: It is completely thermalized for each k-direction pointing radially away from the Dirac point, but at the same time it is strongly anisotropic. The anisotropy is most pronounced for low pump fluences. Increasing the pump fluence from several nJ/cm² to µJ/cm² results in a transition from anisotropic to isotropic distributions. We suggest that this is associated with optical phonon scattering that is enabled at high electron temperatures. The experimental results are compared with microscopic theory that takes into account combined effects of Coulomb and carrier-phonon scattering.
References
[1] J. Rioux, J.E. Sipe, Physica E 45, 1-15 (2012)
[2] M. Mittendorff, T. Winzer, E. Malic, A. Knorr, C. Berger, W. A. de Heer, H. Schneider, M. Helm and S. Winnerl, Nano Lett. 14, 1504-1507 (2014)
Keywords: graphene; ultrafast dynamics
Involved research facilities
- Radiation Source ELBE DOI: 10.17815/jlsrf-2-58
Related publications
- DOI: 10.17815/jlsrf-2-58 is cited by this (Id 22898) publication
-
Poster
German THz Conference 2015, 08.-10.06.2015, Dresden, Deutschland
Permalink: https://www.hzdr.de/publications/Publ-22898
Pressure-induced shift of energy levels and structural phase transition in CdSe/ZnS quantum dots
Tauch, J.; Braun, J. M.; Keller, J.; Hinz, C.; Haase, J.; Seletskiy, D. V.; Leitenstorfer, A.; Pashkin, A.
Abstract
Electronic band structure of CdSe/ZnS quantum dots under high pressures is studied using fluorescence spectroscopy. We observe a strong blue shift of about 40 meV/GPa for the emission line at 655 nm. At moderate pressures (below 3GPa) this shift is linear and it is dominated by increase of the fundamental band gap of CdSe under pressure [1,2]. In contrast to bulk CdSe where the fluorescence is quenched above 3GPa as a result of the phase transition into the rock-salt structure [3,4], the CdSe/ZnS quantum dots remain structurally stable up to 6.5GPa. This structural robustness together with the high fluorescence yield and the large pressure-induced line shift, exceeding that of bulk ruby crystals by a factor of 40, make CdSe quantum dots a promising candidate for precise pressure calibration at moderate pressures.
[1] W. Shan et al., Appl. Phys. Lett. 84, 67 (2004).
[2] B. S. Kim et al., J. Appl. Phys. 89, 8127 (2001).
[3] S. H. Tolbert and A. P. Alivisatos, J. Chem. Phys. 102, 4642 (1995).
[4] S. H. Tolbert and A. P. Alivisatos, Science 265, 373 (1994).
Keywords: quantum dots; high pressure; CdSe/ZnS
-
Poster
DPG-Frühjahrstagung 2015, 15.-20.03.2015, Berlin, Deutschland
Permalink: https://www.hzdr.de/publications/Publ-22897
Investigations on the polarization dependent carrier excitation in graphene with low energetic photons
Otto, J.; Mittendorff, M.; Winzer, T.; Malic, E.; Knorr, A.; Schneider, H.; Helm, M.; Winnerl, S.
Abstract
We demonstrate that in graphene a nonequelibrium charge carrier distribution retains its anisotropic nature on a 10 ps timescale if the photon energy is below the optical phonon energy. Recently evidence for an anisotropic carrier distribution has been found in near-infrared pump-probe experiments with varied angle between the orientation of pump and probe polarization [1]. This anisotropy vanishes after 150 fs due to electron optical-phonon scattering. Extending this study to the mid-infrared range (E_Photon = 74 meV), i.e. to energies below the optical phonon energy, allows to strongly suppress this scattering mechanism. In accord with microscopic theory, traces of an anisotropic distribution on a 10 ps timescale are found. Note that carrier-carrier scattering, acting on a 10 fs timescale, is mainly colinear and therefor preserves the anisotropic distribution on rather long timsecales.
[1] M. Mittendorff, T. Winzer, E. Malic, A. Knorr, C. Berger, W. A. de Heer, H. Schneider, M. Helm and S. Winnerl Nano Lett. 2014, 14, 1504-1507
Keywords: graphene; ultrafast dynamics
Involved research facilities
- Radiation Source ELBE DOI: 10.17815/jlsrf-2-58
Related publications
- DOI: 10.17815/jlsrf-2-58 is cited by this (Id 22896) publication
-
Lecture (Conference)
DPG-Frühjahrstagung, 15.-20.03.2015, Berlin, Deutschland
Permalink: https://www.hzdr.de/publications/Publ-22896
Application of CFD towards the thermo-hydraulic analysis of Spent Fuel Pool accidents
Oertel, R.; Krepper, E.; Lucas, D.
Abstract
The thermo-hydraulic analysis of Spent Fuel Pool accident scenarios is predominantly carried out using one-dimensional codes. This implies that simplified assumptions have to be made for the flow paths around the storage racks and inside the reactor building. Here, CFD is employed to investigate the convective phenomena involved and to examine their relevance for the cooling of the individual fuel assemblies, which themselves are modeled as porous bodies. The paper includes a discussion of relevant thermohydraulic aspects and the modeling on the fuel assembly scale as well as the reactor building scale. First preliminary large scale simulations are presented, using the design of Fukushima’s Unit 4 with the corresponding Spent Fuel Pool loading as a test case. A loss of coolant due to the outage of the cooling system and subsequent boil-off is assumed, leading to partially or fully uncovered fuel assemblies. The emerging flow paths are described qualitatively. This ongoing work gives an outlook how CFD can help to study the safety of Spent Fuel Pools as a standalone tool or by delivering input to one-dimensional codes.
Keywords: Spent Fuel Pool Safety; Boil-Off/Drainage Scenarios; CFD; Porous-Body-Approach
-
Contribution to proceedings
16th International Topical Meeting on Nuclear Reactor Thermalhydraulics(NURETH-16), 30.08.-04.09.2015, Chicago, USA -
Lecture (Conference)
The 16th International Topical Meeting on Nuclear Reactor Thermal Hydraulics (NURETH-16), 30.08.-04.09.2015, Chicago, USA
Permalink: https://www.hzdr.de/publications/Publ-22895
Industrial challenges in ion beam processing and metrology in the 3D era
England, J.; Möller, W.
Abstract
Ion beam mechanisms present in plasma doping have been investigated by comparing SIMS measurements of Ge implants into deposited layers of As on Si wafers to planar dynamic ion beam models of the implants and SIMS analyses. Industrial devices are overcoming the limitations of lateral scaling by using the vertical direction. The same modelling approach would be valuable for interpreting 1.5D SIMS analyses of plasma doping of 3D-NAND test structures but 3D dynamic codes do not yet have all the capabilities to allow this. The required features are being developed within a static 3D code, TRI3DSTP, which has been used to qualitatively explain the good uniformity of a P plasma doping process and indicate where more quantitative explanations will be possible once the full dynamic capabilities are available.
Keywords: 3D NAND; Ion beam modelling; Ion-implantation; Plasma doping
Involved research facilities
- Ion Beam Center DOI: 10.17815/jlsrf-3-159
Related publications
- DOI: 10.17815/jlsrf-3-159 is cited by this (Id 22894) publication
-
Nuclear Instruments and Methods in Physics Research B 365(2015), 105-109
DOI: 10.1016/j.nimb.2015.03.016
ISSN: 0168-583X
Cited 2 times in Scopus
Permalink: https://www.hzdr.de/publications/Publ-22894
P1505 - Komplementärer Widerstandsschalter
Bürger, D.; Du, N.; Schmidt, H.; Skorupa, I.; You, T.
Abstract
Die Erfindung betrifft eine schaltbare Widerstandsstruktur (3) mit einem ersten elektrisch leitfähigen Kontakt (T1), einem zweiten elektrisch leitfähigen Kontakt (T2), einer ersten piezoelektrischen oder ferroelektrischen Schicht (11a) und einer zweiten piezoelektrischen oder ferroelektrischen Schicht (11b), wobei die beiden piezoelektrischen oder ferroelektrischen Schichten miteinander in körperlichem Kontakt stehen und zwischen den beiden Kontakten angeordnet sind, wobei mindestens einer der Kontakte mit der betreffenden piezoelektrischen oder ferroelektrischen Schicht einen Schottky-Kontakt bildet und wobei die zweite piezoelektrische oder ferroelektrische Schicht (11b) mit mindestens einem zusätzlichen Metall und/oder einem zusätzlichen Halbmetall als Dotand dotiert ist.
-
Patent
EP2940749 - Offenlegung 04.11.2015
Permalink: https://www.hzdr.de/publications/Publ-22893
Experimental investigation of electromagnetic stirring affecting the mould flow in a liquid metal model
Willers, B.; Eckert, S.; Barna, M.; Reiter, J.
Abstract
In this work an experimental study using a 1:3 scale acrylic glass model of the round bloom caster from voestalpine Stahl Donawitz GmbH is presented. The model experiment uses the eutectic alloy GaInSn at room temperature. An electromagnetic stirrer was installed at the mould producing a rotating magnetic field (RMF). The flow field inside the mould was measured using the ultrasound Doppler velocimetry (UDV). Up to 10 ultrasonic transducers were employed simultaneously in order to obtain a two-dimensional reconstruction of the flow structure. The experiment provides an extensive and valuable data base for validation of numerical methods. The application of electromagnetic fields for flow and solidification control in continuous casting will be a crucial point of our future work
Keywords: Continuous casting; electromagnetic stirring; rotating magnetic field; physical modelling; flow measurements; Ultrasound Doppler velocimetry
-
Contribution to proceedings
Experimental investigation of electromagnetic stirring affecting the mould flow in a liquid metal model, 15.-19.06.2015, Düsseldorf, Deutschland
European Steel Technology and Application Days, 978-3-00-049542-7 (CD)
Permalink: https://www.hzdr.de/publications/Publ-22892
Fluorinated PET tracers for molecular imaging of σ1 receptors in the central nervous system.
Weber, F.; Brust, P.; Laurini, E.; Pricl, S.; Wünsch, B.
Abstract
At first the role of σ1 receptors in various neurological, psychiatric and neurodegenerative disorders is discussed. In the second part, the principle of positron emission tomography (PET) is described and the known fluorinated PET tracers for labeling of σ1 receptors are presented. The third part focuses on fluoroalkyl substituted spirocyclic PET tracers, which represent the most promising class of fluorinated PET tracers reported so far. The homologous fluoroalkyl derivatives 12-15 show high σ
-
Book chapter
Smith, S. B.; Su, T.-P.: Sigma Receptors: Their Role in Disease and as Therapeutic Targets, Berlin, Heidelberg: Springer, 2017, 978-3-319-50172-7, 31-48
DOI: 10.1007/978-3-319-50174-1_4
Cited 11 times in Scopus
Permalink: https://www.hzdr.de/publications/Publ-22891
Accretion rate of IDPs onto the Earth by means of 53Mn and 41Ca AMS measurement in Antarctic snow
Gomez Guzman, J. M.; Bishop, S.; Faestermann, T.; Feige, J.; Fimiani, L.; Hain, K.; Kipfstuhl, S.; Korschinek, G.; Ludwig, P.; Merchel, S.; Rodrigues, D.; Sterba, J.; Welch, J.; Weller, R.
Abstract
Interplanetary Dust Particles (IDPs) are small grains, a few hundred micrometers in size and mainly originated in the Asteroid Belt. During their flight to the Earth they are irradiated by GCR and SCR and 41Ca (T1/2 = 1.03 × 105) and 53Mn (T1/2 = 3.68 × 106 yr) are formed.
Since there are no significant terrestrial sources for those radionuclides they can be used as a key tracer to determine the accretion rate of IDPs onto the Earth. For this project, 550 kg of snow have been collected at the Antarctic German station Kohnen to be processed to extract 41Ca and 53Mn. Also the filter used will be processed to check the existence of IDPs surviving evaporation during their entry in the atmosphere. The AMS measurements will be made at the MLL in Garching, a facility with sensitivity down to 10−16 for 41Ca and 10-14 for 53Mn.
Keywords: accelerator mass spectrometry; IDP; AMS
-
Lecture (Conference)
DPG Frühjahrstagung des Arbeitskreises Atome, Moleküle, Quantenoptik und Plasmen (AMOP), 29.02.-04.03.2016, Hannover, Deutschland
Permalink: https://www.hzdr.de/publications/Publ-22890
Supernova-produced 60Fe in Earth’s microfossil record
Ludwig, P.; Bishop, S.; Egli, R.; Chernenko, V.; Deneva, B.; Faestermann, T.; Fimiani, L.; Gómez-Guzmán, J. M.; Hain, K.; Korschinek, G.; Hanzlik, M.; Merchel, S.; Rugel, G.
Abstract
It is possible for a nearby supernova (SN) explosion to deposit a fraction of its ejecta on Earth. Due to the lack of significant anthropogenic and cosmogenic background, 60Fe (T1/2 = 2.6 Ma) is perfectly suited to serve as a radioactive tracer of recent SN events. The ratio of 60Fe/Fe was measured in over 100 samples extracted from two sediment cores from the Eastern Equatorial Pacific. The AMS samples were produced using a carefully tuned chemical leaching technique that specifically targets fine-grained iron-oxides, such as magnetofossils.
Magnetofossils are the remains of magnetosome chains, built up by magnetotactic bacteria, which are abundantly present in our sediment, as shown by magnetic analysis and electron microscopy.
The AMS samples were measured at the GAMS setup at the Maier-Leibnitz-Laboratory in Garching, where the use of a gas-filled magnet for isobaric suppression provides a sensitivity of 60Fe/Fe ≈ 5 x 10-17.
Our results reveal a 60Fe signature over a time-range of about 1.7-2.7 Ma, which is attributed to the deposition of SN debris.
Keywords: accelerator mass spectrometry; supernova
Involved research facilities
- Ion Beam Center DOI: 10.17815/jlsrf-3-159
Related publications
- DOI: 10.17815/jlsrf-3-159 is cited by this (Id 22889) publication
-
Poster
DPG Frühjahrstagung des Arbeitskreises Atome, Moleküle, Quantenoptik und Plasmen (AMOP), 29.02.-04.03.2016, Hannover, Deutschland
Permalink: https://www.hzdr.de/publications/Publ-22889
Analysis of activated sludge aerated by membrane and monolithic spargers with ultrafast X-ray tomography
Sommer, A.-E.; Wagner, M.; Reinecke, S.; Bieberle, M.; Barthel, F.; Hampel, U.
Abstract
Up to 80 % of the total energy budget of wastewater treatment plants is consumed by the activated sludge process. Current optimizations are mostly based on limited instrumentation for single points of measurement which cannot express the complex hydrodynamic and biochemical processes. Therefore, the ultrafast electron beam X-ray tomography system ROFEX of HZDR is used as a new measurement technique to capture the temporal evolution of the multiphase flow in the opaque active sludge. A detailed study has been carried out in a vertical column of 3.5 m height at HZDR to obtain an improved understanding of the hydrodynamics of aerated sludge and an evaluation of different aerators. The target parameters are bubble size distribution, equivalent Sauter mean diameter of the bubbles, bubble rise velocity and local gas hold-up under the variation of sparger type (rubber, monolithic material), gas flow rate, rheology of the fluid (deionized water, salty water, sludge) and height in the liquid column. Therefore, in-house developed advanced image analysis algorithms were applied to the reconstructed tomographic images, which are also presented in the paper. The experiments showed that with ROFEX reliable measurement data of opaque multiphase flows is produced and is expected to be used in further investigations for the validation of computational fluid dynamics (CFD) models. The different sparger types showed comparable hydrodynamic performance.
Keywords: Ultrafast X-ray tomography; activated sludge; aeration
Involved research facilities
- TOPFLOW Facility
-
Flow Measurement and Instrumentation 53A(2017), 18-27
DOI: 10.1016/j.flowmeasinst.2016.05.008
ISSN: 0955-5986
Cited 10 times in Scopus
Permalink: https://www.hzdr.de/publications/Publ-22888
Calculation of Debye-Scherrer diffraction from polycrystalline samples under an arbitrary stress field
Macdonald, M. J.; Vorberger, J.; Drake, R. P.; Glenzer, S. H.; Fletcher, L. B.
Abstract
Calculating Debye-Scherrer diffraction patterns from polycrystalline materials under dynamic compression has been done in the Voigt (iso-strain) limit or in the Reuss (iso-stress) limit for small deviatoric stresses. These methods are appropriate for materials with low yield strength, where only small deviations from the hydrostat can be supported by the crystal structure or materials with low elastic anisotropy where the Voigt limit is valid. Here we present a method to calculate Debye-Scherrer diffraction patterns from polycrystalline samples under an arbitrary stress field. This method can calculate the strain tensor for each crystallite and can account for arbitrary sample texture and probe x-ray sources.
Keywords: x-ray; crystallography; stress; strain
-
Applied Physics Letters 119(2016)21, 215902
DOI: 10.1063/1.4953028
Cited 15 times in Scopus
Permalink: https://www.hzdr.de/publications/Publ-22887
Secondary Neutron Field at the Dresden Proton Therapy
Lutz, B.; Enghardt, W.; Swanson, R.; Fiedler, F.
Abstract
Particle therapy is a strongly growing field in cancer therapy. Almost 60 treatment centres are currently operating worldwide and the total number will reach more than 90 by 2017~\cite{PTCOG}. The majority of the centres uses protons to treat patients.
With the increasing importance of particle therapy, the development of application-specific monitoring systems has received a significant boost. On the one side, there are the radio-protection questions like the secondary dose to patients or to radio-sensitive equipment. On the other side, there are the methods that intend to verify the correct application of the treatment dose, during or short after the treatment, like prompt-gamma-imaging or -timing, or PET. For both groups of measurements, a good understanding of the secondary radiation field is crucial.
The greatest challenge in determining the secondary radiation field comes from neutrons. The spectra of the neutrons, generated by protons of therapeutic energies, extend far beyond the specification of most commercially available dosimeters. Additionally, the generated neutron fields are spatially nonuniform and in case of passive field formation strongly dependent on the operational setting. Combined with the very limited spatial and spectral resolution of the available neutron detectors, many details of the field cannot be experimentally resolved. Therefore, a dependable measurement of the neutron field requires a detailed simulation of the neutron generation in the treatment system.
The OncoRay treatment centre at the University Hospital Carl Gustav Carus operates an IBA universal nozzle that is capable of providing both scattered and scanned proton beams. This nozzle has been modelled in detail by means of the TOPAS software~\cite{TOPAS}. TOPAS provides a text-file based interface to Geant4~\cite{Geant4} Simulation Toolkit with focus on proton therapy applications.
The talk gives an overview of the specific implementation of the IBA nozzle. It presents the predicted secondary neutron fields and discusses how these depend on the operational parameters of the nozzle. Finally the results are compared to experimental measurements.
-
Lecture (Conference)
1st Workshop Helmholtz Cross Program Activity - Querschnittsthema Strahlenforschung “Sekundäre Neutronen in Medizin und Strahlenschutz”, 24.-26.11.2015, München, Deutschland
Permalink: https://www.hzdr.de/publications/Publ-22886
Metals: Key enablers of a Circular Economy
Reuter, M. A.
Abstract
Base metals such as copper, lead, nickel, cobalt, zinc etc. form the basic crucial carrier metals for a sustainable society – the Web of Metals. This paper discusses the special and crucial role these metals have in acting as enablers in any recycling efforts as they carry and release important and vital minor elements at the heart of high-tech applications and products. Through examination of the rising needs for such carriers, this paper examines the approach and technologies which need to be considered by any producer of base metals. Attention is paid to the limits and extent of this carrier role in the typical processing of materials. Examples of specialised technology and flowsheet needs are presented with consideration given to a “whole of chain” or Systems-Integrated Metal Production (SIMP) approach as a cornerstone of a circular economy. Also outlined are the challenges facing not only producers, but legislators who need to consider the balance between providing our societal needs with baseline technology infrastructure requirements for valuable metals extraction. In summary, the message of this paper states simply that not only is the criticality of metals important but the criticality of the infrastructure (Infrastructure Criticality) that can recover metals from complex designed “mineral” mixtures. Base metals are at the heart of a Circular Economy, therefore key enablers of the Internet-of-Metallurgical-Things.
Keywords: Resource efficiency base metals; Recycling; System integration; Design for Recycling (DfR)
-
Invited lecture (Conferences)
Cleantech Innovations in Minerals Production, 08.-10.09.2015, Helsinki, Finnland
Permalink: https://www.hzdr.de/publications/Publ-22885
Ultrafast Insulator-Metal Transition in VO2 Driven by High-field THz Excitation
Pashkin, A.; Mayer, B.; Schmidt, C.; Grupp, A.; Oelmann, J.; Marvel, R. E.; Haglund Jr., R. F.; Oka, T.; Leitenstorfer, A.
Abstract
Vanadium dioxide (VO2) is a prime example of a transition metal oxide with a sharp insulator-metal transition (IMT) at 340 K accompanied by a change of the lattice symmetry. A possibility to induce the metallic state in VO2 by electric field has attracted a lot of attention due to its potential applications in optics and high-speed electronics. However, numerous efforts to control the electronic state by applied electric bias have demonstrated that the switching mechanism is governed by resistive heating, dramatically limiting the operation speed. Recent developments in generation of high-field broadband THz transients offer an attractive way to apply extremely high electric fields on ultrashort timescales.
Here, we demonstrate an IMT in VO2 thin films driven by high-field multi-THz transients on a sub-100 fs timescale. Our broadband and phase-stable THz transients with extremely high peak electric fields of up to 17 MV/cm are generated via difference frequency mixing in a GaSe crystal. A typical excitation transient and the induced relative transmission change T/T traced by 8-fs-short near-infrared pulses are shown in Fig. 1(a). An ultrafast decrease of the transmission indicates the THz-driven switching into the metallic state, succeeded by a relatively slow relaxation on longer timescales. Besides that, the lattice dy-namics related to the coherent wave packet motion of the vanadium dimers manifests itself as an oscillation at a frequency of 5.9 THz [Fig. 1(a)]. Our experiments show that the observed non-thermal switching into a metastable metallic state is governed solely by the amplitude of the applied THz field. In contrast to resonant near-infrared excitation below the threshold fluence, no signatures of excitonic self-trapping are observed down to the lowest fluences of the THz excitation.
Our results can be understood as the generation of spatially separated charge pairs and a cooperative transition into a delocalized metallic state by THz field-induced tunneling. The total density of the delo-calized carriers proportional to the increase in optical conductivity Δσ1 at THz frequencies depicted in Fig. 1(b) shows a highly nonlinear dependence on the peak excitation field expected for a many-body tunneling process. We find good agreement with theoretical equation describing pair production in a Mott insulator and determine an electronic correlation length of 2.1 Å.
Keywords: terahertz; insulator-to-metal transition; non-thermal transition; field-induced tunneling
-
Lecture (Conference)
German THz conference, 08.-10.06.2015, Dresden, Germany
Permalink: https://www.hzdr.de/publications/Publ-22884
Fully intensity and timing jitter compensated ultra-fast experiments at accelerator-driven photonsources at high repetition rates
Kovalev, S.; Green, B.; Golz, T.; Stojanovic, N.; Fisher, A. S.; Kampfrath, T.; Gensch, M.
Abstract
Timing jitter and power instabilities are crucial parameters which greatly reduce the applicability of accelerator driven light sources for time-resolved experiments. In this contribution we present a technique that allows achieving few 10 fs time-resolution in experiments operating at cw repetition rates of up to 100 kHz by employing high repetition rate data acquisition. The method employs a fs-level arrival time monitor based on electro-optic sampling of residual pulses from a coherent diffraction radiator and a fast THz detector allowing for pulse to pulse detection of arrival time and pump intensity. The monitor can operate at high repetition rates cw (presently up to a few 100 kHz) and low electron bunch charges (sub pC). The prototype device has been tested at the quasi CW SRF accelerator (ELBE) by performing an ultra-fast THz driven magnetization dynamics experiment. Our method has high potential to provide few fs level timing on next generation large scale X-ray photon sources based on high repetition rate electron accelerators such as LCLSII. A demonstrator aiming at operation up to 4.7 MHz is under development for the European X-FEL.
Keywords: Timing Jitter; ultrafast experiments; super radiance
Involved research facilities
- Radiation Source ELBE DOI: 10.17815/jlsrf-2-58
Related publications
- DOI: 10.17815/jlsrf-2-58 is cited by this (Id 22883) publication
-
Lecture (Conference)
International beam instrumentation conference 2015, IBIC2015., 13.09.2015, Melbourne, Australia
Permalink: https://www.hzdr.de/publications/Publ-22883
Ermittlung der Referenztemperatur T0 nach dem Master-Curve-Konzept mit Miniatur-C(T)-Proben
Viehrig, H.-W.; Houska, M.
Abstract
Mini 0,16T-C(T)-Proben wurden aus halben ISO-V-Proben von zwei RDB-Stählen und einem RDB-Schweißgut hergestellt und nach ASTM E1921 geprüft. Die mit diesen Proben ermittelten und auf eine Dicke von 1T (25,4 mm) umgerechneten Bruchzähigkeiten, KJc(1T), folgen dem Verlauf der Master Kurven. Mit 1T-, 0,5T-, 0,25T und 0,16T-C(T)-Proben aus RDB-Stahl 22 NiMoCr 3-7 wurden vergleichbare Referenztemperaturen T0 bestimmt. Die geringe Messkapazität, KJc(limit), der 0,16T-C(T)-Proben begrenzt das Messfenster auf einen Temperaturbereich von T0 minus 15 K bis 50 K. Die Seitkerbung der 0,16T-C(T)-Proben bewirkt eine gleichmäßigere Spannung und Verteilung der Rissinitiierungsorte über die Nettoprobendicke (Ermüdungsrissfront).
Miniature 0.16T-C(T) specimens were machined from halves of already tested ISO-V specimens of two RPV steels and one RPV multilayer weld metal. The specimens were tested according to ASTM E1921. The progression of the 1T (25.4 mm) size adjusted fracture toughness, KJc(1T) values follow the Master Curve. The T0 values determined with 1T , 0.5T-, 0.25T- and 0.16T-C(T) specimens of 22 NiMoCr 3-7 RPV steel are comparable. The small measuring capacity of the 0.16T-C(T) specimen limits the test temperature window to T0 minus 15 K to 50 K. Side grooving results in a more uniform stress and distribution of cleavage initiation sites along the net thickness (fatigue crack front).
Keywords: Spaltbruch; Bruchzähigkeit; Master Curve Konzept; C(T)-Proben; Seitkerbung; cleavage fracture; fracture toughness; Master Curve approach; C(T) specimen; side-grooving
-
Contribution to proceedings
48. Tagung des DVM-Arbeitskreises Bruchvorgänge und Bauteilsicherheit, 16.-17.02.2016, Freiburg, Deutschland
Bruchmechanische Werkstoff- und Bauteilbewertung: Beanspruchungsanalyse, Prüfmethoden und Anwendungen, DVM-Bericht 247:, Berlin: DVM, 1616-4687, 229-239
Permalink: https://www.hzdr.de/publications/Publ-22882
Ion Implantation Induced Damage in Oxide Dispersion Strengthened Steels and FeCr Alloys Investigated by DB and cDB
Anwand, W.; Heintze, C.; Leguey, T.
Abstract
FeCr alloys and oxide dispersion strengthened (ODS) FeCr steels are candidates for structural materials for Generation IV and fusion reactors, owing their advantageous physical and chemical properties for such applications as, e.g., resistance against oxidation, creep and radiation.
For an optimal steel composition, depending on the application, it is important to understand how alloying components and oxide additives affect the materials behaviour to irradiation. For this purpose, Fe-Cr alloys have been employed as model materials in irradiation experiments and subsequent characterization of irradiation damage. Ion implantation was demonstrated an efficient tool for simulation of radiation damage similar to that in fission/fusion power plant materials, but without any induced activation.
FeCrNiSiP samples with two Cr contents of 5 wt.% and 9 wt.% were implanted with 5 MeV Fe ions at different temperatures with a damage of 0.1 displacements per atom (dpa) and 0.5 dpa, respectively. The influence of the alloying elements on the evaluation of the damage after ion implantation was investigated for the complete FeCrNiSiP alloy and separately for each FeCr added with the single alloying elements.
Furthermore model Fe14wt.%Cr alloys and two ODS Fe14Cr steels with 0.3wt.%Y2O3 and with and without Ti and W additions were implanted at low temperature with 1 MeV Fe ions up to a high damage of 15 dpa.
A slow positron beam has been used in order to investigate the depth dependence of the ion implantation induced vacancy-type defect in the materials by single Doppler broadening (DB) measurements with positron energies from 30eV to 35keV, corresponding to a depth from 1 nm down to 3 µm. Furthermore, coincidence DB measurements at selected positron energies were applied for a more precise examination of a possible defect decoration of the open volume by alloying elements.
Slow positron beam techniques turned out to be an effective tool for the characterization of open-volume defects after ion implantation. It could be shown that a Ni addition to FeCr led to an increase of the open-volume defects after ion implantation, whereas Si or P reduced them. A minimal damage could be detected for the complete alloy FeCrNiSiP.
A lower Cr content of 5wt.% is advantageous against 9wt.% for a defect annealing during implantation at temperatures below 450 °C. At 450 °C all defects annealed out already during implantation.
The influence of Y2O3 nanoparticles on the stabilization of defects in FeCr steels could be demonstrated by DB and cDB measurements and will be discussed in detail.
Keywords: FeCr alloys; Oxide Dispersion Strengthened Steels; ion implantation induced damaged; positron annihilation spectroscopy
Involved research facilities
- Radiation Source ELBE DOI: 10.17815/jlsrf-2-58
Related publications
- DOI: 10.17815/jlsrf-2-58 is cited by this (Id 22881) publication
-
Lecture (Conference)
17th International Conference on Positron Annihilation, 20.-25.09.2015, Wuhan, PR China
Permalink: https://www.hzdr.de/publications/Publ-22881
Multiphase flow imaging: Techniques and Applications
Schubert, M.; Hampel, U.
Abstract
Multiphase flows are omnipresent in many industrial sectors and engineering disciplines, such as petroleum and chemical engineering, nuclear engineering and thermal hydraulics, and fluid me-chanics and multiphase CFD.
Multiphase flows of gases, liquids, and/or solids are often highly dynamic and fully opaque, housed in pressurized and large vessels and thus, are hardly accessible with today’s commercial diagnostic tools and standard instrumentation. In turn, improvements in process efficiency, sustainability and safety depend on detailed insights – often at CFD-grade – at different scales.
The seminar will give an overview about recent developments in advanced multiphase flow sensors and imaging techniques for in-detail flow analyses, with a focus on measurement with high resolu-tion in space and/or time. Recently pioneered imaging techniques are the wire-mesh sensor, ultrafast X-ray tomography and high-resolution gamma-ray tomography.
In particular, the underlying principles of the techniques will be shown together with a variety of application examples, such as sand erosion in pipe flow, gas entrainment in centrifugal pumps and dispersive gas-liquid mixing in static mixers.
Keywords: imaging techniques; tomography; wire-mesh sensor; applications
Involved research facilities
- TOPFLOW Facility
-
Lecture (others)
SABIC Process Seminar, 05.10.2015, Geleen, Niederlande
Permalink: https://www.hzdr.de/publications/Publ-22880
Hydrodynamics of Concurrent Gas-Liquid Flows in Inclined Rotating and Floating Packed Beds
Dashliborun, A. M.; Larachi, F.; Härting, H.-U.; Schubert, M.; Schleicher, E.
Abstract
The effects of floating vessel motions and reactor rotation on the hydrodynamic behaviour of multiphase flows in porous media were studied. For elucidating such effects, laboratory-scale packed bed systems with co-current gas-liquid flow were subjected to different types of motion by using a hexapod ship motion simulator and a hollow shaft rotary actuator. The hydrodynamic characteristics in terms of bed overall pressure drop, liquid saturation, gas-liquid segregation, and flow regime transition was experimentally studied. A capacitance wire mesh sensor (WMS) and a compact gamma-ray tomography system (CompaCT) were positioned firmly on, respectively, the floating packed bed and the inclined rotating packed bed to visualize the two-phase flow patterns in terms of local liquid saturation distribution. The response of pressure drop, liquid saturation, and flow regime transition to the bed motions was monitored and compared to those corresponding to the static upright and 15°-inclined configurations. The results indicated that the known characteristics of the conventional trickle bed reactor cannot be transferred one to one on those of the moving reactor configurations.
Keywords: Two-phase flow; moving packed bed; hydrodynamics; WMS; gamma tomography
-
Lecture (Conference)
7th International Symposium on Process Tomography, 01.-03.09.2015, Dresden, Deutschland
Permalink: https://www.hzdr.de/publications/Publ-22879
High field superconducting properties of Ba(Fe1−xCox)2As2 thin films
Hänisch, J.; Iida, K.; Kurth, F.; Reich, E.; Tarantini, C.; Jaroszynski, J.; Förster, T.; Fuchs, G.; Hühne, R.; Grinenko, V.; Schultz, L.; Holzapfel, B.
Abstract
In general, the critical current density, Jc, of type II superconductors and its anisotropy with respect to magnetic field orientation is determined by intrinsic and extrinsic properties. The Fe-based superconductors of the ‘122’ family with their moderate electronic anisotropies and high yet accessible critical fields (Hc2 and Hirr) are a good model system to study this interplay. In this paper, we explore the vortex matter of optimally Co-doped BaFe2As2 thin films with extended planar and c-axis correlated defects. The temperature and angular dependence of the upper critical field is well explained by a two-band model in the clean limit. The dirty band scenario, however, cannot be ruled out completely. Above the irreversibility field, the flux motion is thermally activated, where the activation energy U0 is going to zero at the extrapolated zero-kelvin Hirr value. The anisotropy of the critical current density Jc is both influenced by the Hc2 anisotropy (and therefore by multi-band effects) as well as the extended planar and columnar defects present in the sample.
Involved research facilities
- High Magnetic Field Laboratory (HLD)
-
Scientific Reports 5(2015), 17363
DOI: 10.1038/srep17363
ISSN: 2045-2322
Cited 47 times in Scopus
Permalink: https://www.hzdr.de/publications/Publ-22878
CFD for Two-Phase Flows: Status, Recent Trends and Future Needs
Lucas, D.; Laurien, E.
Abstract
This presentation discusses the status and the future developments of CFD-methods for multiphase flows.
Keywords: multiphase; CFD; bubbly flow; segregated flow
Involved research facilities
- TOPFLOW Facility
-
Invited lecture (Conferences)
46th Annual Meeting on Nuclear Technology, 05.-07.05.2015, Berlin, Deutscland
Permalink: https://www.hzdr.de/publications/Publ-22877
Dispersed Flow Modelling - Multiple-Size Group Modelling - MUSIG
Krepper, E.
Abstract
The lesson 7 of the "Short Course on Multiphase Flow Modelling" deals with the simulation of two phase flow. For low gas fractions the Euler/Euler approach with continuous liquid and dispersed gas can be applied. A populatioon balance model approach is described. Model validations and model applications are presented.
Keywords: CFD; Two fluid model; Bubbly flow; population balance; MUSIG
Involved research facilities
- TOPFLOW Facility
-
Lecture (Conference)
13th Multiphase Flow Conference and Short Course: Simulation, Experiment and Application, 24.-26.11.2015, Dresden, Germany -
Lecture (Conference)
14th Multiphase Flow Conference and Short Course: Simulation, Experiment and Application, 08.-10.11.2016, Dresden, Germany
Permalink: https://www.hzdr.de/publications/Publ-22876
Interfacial heat and mass tansfer models
Krepper, E.; Scheuerer, G.
Abstract
The lesson 5 of the "Short Course on Multiphase Flow Modelling" deals with the simulation of mass and energy exchange between the phases based on the two fluid model approach. After the basic principles the lesson describes the simulation of subcooled boiling and the simulation of cavitation processes.
Keywords: CFD; Two fluid model; heat transfer; mass transfer; boiling; cavitation
-
Lecture (Conference)
13th Multiphase Flow Conference and Short Course: Simulation, Experiment and Application, 24.-26.11.2015, Dresden, Germany
Permalink: https://www.hzdr.de/publications/Publ-22875
User facilities for Positron Annihilation Spectroscopy (PAS) at Helmholtz-Zentrum Dresden-Rossendorf (HZDR)
Anwand, W.; Butterling, M.; Wagner, A.
Abstract
Three user dedicated facilities of PAS are built at the Institute of Radiation Physics of HZDR. The first equipment, a mono-energetic slow positron beam with 22Na as positron source, is mainly used for depth dependent Doppler broadening spectroscopy of defects in solids. The other two facilities are driven in connection with a superconducting electron linear accelerator ELBE (Electron Linac for beams with high Brilliance and low Emittance), where the positrons are created by bremsstrahlung and pair production: the Gamma-induced positron annihilation spectroscopy (GiPS) and the pulsed mono-energetic positron beam (MePS).
After an explanation of the fundamentals of PAS, the talk will present an introduction in the set-up and functionality of these three facilities. On the basis of concrete examples the usefulness of the facilities for the investigation of open-volume defects of small size and low concentration in solids will be demonstrated.
At the end of the presentation, a short outline of the procedure for application of PAS beam time will be given.
Keywords: user facilities; positron annihilation spectroscopy
Involved research facilities
- Radiation Source ELBE DOI: 10.17815/jlsrf-2-58
Related publications
- DOI: 10.17815/jlsrf-2-58 is cited by this (Id 22874) publication
-
Lecture (others)
Seminar-Vortrag, 30.11.2015, Prague, Czech Republic
Permalink: https://www.hzdr.de/publications/Publ-22874
CFD Simulations on TOPFLOW-PTS Tests
Apanasevich, P.; Lucas, D.; Merigoux, N.; Badillo, A.; Roy, J.
Abstract
This talk presents the main results obtained during the European project NURESAFE on CFD-modelling of a two-phase Pressurized Thermal Shock szenario. The focus is on simulations on steam-water TOPFLOW-PTS experiments.
Keywords: PTS; TOPFLOW; CFD; two-phase flow
Involved research facilities
- TOPFLOW Facility
-
Lecture (Conference)
2nd NURESAFE Open Seminar, 03.-04.11.2015, Brussels, Belgium
Permalink: https://www.hzdr.de/publications/Publ-22873
Gittersensorbasierte Visualisierung von Verweilzeit- und Geschwindigkeitsverteilungen auf einem Siebboden
Schubert, M.; Piechotta, M.; Beyer, M.; Hampel, U.
Abstract
In vielen Trennkolonnen werden Siebböden eingesetzt, bei der der Stoffaustausch zwischen Dampf- und Flüssigphase in der Sprudelschicht erfolgt. Eine ungleich-mäßige Überströmung des Bodens, z. B. aufgrund von Wölbungen oder Neigungen des Bodens sowie durch ungleichmäßige Überströmung der Wehre, kann dabei die Trennwirkung deutlich verschlechtern. Nach Bell und Solari [AIChE J., 20, 4, 688-695, 1974] kann anstatt aufwendiger Stoffanalysen anhand des Strömungsfelds der Flüssigphase auf die Trennleistung geschlossen werden.
In diesem Beitrag wird eine neue Messmethode zur Ermittlung dieses Strömungsfeldes vorgestellt. Diese basiert auf der hochaufgelösten Analyse der Wehr-zu-Wehr-Überströmung des Bodens mit einem Flüssigkeitstracer anhand eines Leitfähigkeitsgittersensors.
Aus den Tracer-Versuchen lassen sich charakteristische Strömungsparameter, wie die lokale Flüssigkeitsverweilzeit und die Wehr-zu-Wehr-Strömungsgeschwindigkeit extrahieren.
Im Rahmen der Studie wurden unterschiedliche hydraulische Belastungen und Wehranordnungen untersucht und die Überströmung visualisiert und charakterisiert.
Keywords: Siebboden; Destillation; Gittersenor; Verweilzeit
Involved research facilities
- TOPFLOW Facility
-
Lecture (Conference)
Jahrestreffen der Fachgruppen Fluidverfahrenstechnik und Membrantechnik, 26.-27.03.2015, Bremen, Deutschland
Permalink: https://www.hzdr.de/publications/Publ-22872
Gas-Liquid Mass Transfer in a Tubular Reactor with Solid Foam Packing
Mohammed, I.; Bauer, T.; Schubert, M.; Lange, R.
Abstract
Chemical reactors with a fixed-bed of catalyst particles are widely applied for continuous multi-phase processes in the petrochemical, chemical, and biochemical industry. However, the performance of these reactors often suffers from some drawbacks, such as high energy consumption due to high pressure drop as well as mass and heat transfer limitations. One solution is to replace particle catalysts such as tablets, spheres and cylinders with structured catalysts based on open-cell solid foams. This new structure provides large specific surface area of up to 2000 m2/m3 at high open bed porosities between 75 - 97%. As result, the pressure drop of the gas-liquid two-phase flow is comparatively low (Mohammed et al. 2013).
For the design of tubular reactors with foam packings knowledge about gas-liquid mass transfer is important. The goal of this study was to examine the volumetric gas-liquid mass transfer in dependence on operating conditions and foam pore density expressed in the unit pores per inch. The results will be compared to data from the literature for both foam packings and particle packings. The experiments were based on physical desorption and the volumetric mass transfer rates are calculated according the two-film theory by Whitman (1932). The entrance effects were eliminated by performing hydrodynamically identical tests with two different test section lengths, and using the shorter test section results for ‘subtraction’ of entrance effects from the longer test section.
The results show that the volumetric gas-liquid mass transfer coefficient rises with increasing liquid superficial velocity for all foam pore densities studied, while minor effects of the gas velocity were observed. A new correlation to predict the volumetric mass transfer coefficient is derived from the experiments. The gas-liquid mass transfer in foam packings was higher than in trickle beds and beds of rasching rings.
Keywords: solid foam; mass transfer; oxygen desorption; multiphase reactors
-
Lecture (Conference)
ESCRE 2015 - European Symposium on Chemical Reaction Engineering, 27.-30.10.2015, Fürstenfeld, Deutschland
Permalink: https://www.hzdr.de/publications/Publ-22871
Correlating gas-liquid distribution and effective liquid-solid mass transfer coefficient in tubular reactors with solid foam packings
Mohammed, I.; Bauer, T.; Schubert, M.; Lange, R.
Abstract
The performance of multiphase tubular reactors with co-current downward gas-liquid two-phase flow through catalyst packings is strongly affected by the quality of the gas-liquid distribution in the packing. Non-uniform liquid phase distributions in radial and axial direction cause partial catalyst surface wetting, lead to lower catalyst utilization in reduce the effective liquid-solid mass transfer to the catalyst surface [1].
In the recent years, solid foam catalyst packings were studied as promising replacements of randomly arranged catalyst particles [2]. In principle, the open-cell structure of the solid foams allows the liquid radial flow from one cell. However, the ability of solid foams to counterbalance liquid maldistribution and the liquid spreading behavior was not yet studies. The aim of this work is to investigate the cross-sectional liquid saturation distribution in a tubular column packed with solid foams and its effects on the liquid-solid mass transfer coefficient.
The axial evolution of the gas-liquid distribution patterns in solid foam packings of different pore densities has been experimentally studied using wire-mesh sensors installed at different axial heights. Both time-averaged cross-sectional liquid saturation patterns and liquid maldistribution factors were determined for different pre-wetting modes and distributor designs. In addition, effective liquid-solid mass transfer coefficients were determined based on a modified electrochemical limiting diffusion current method and correlated with the maldistribution.
The results indicate that a uniform initial distribution above the foam packing is the most important factor for a good wetting of the solid foam surface. Accordingly, a proper selection of an appropriate liquid distributor is essential for a successful application of catalytic active solid foams. To improve the homogeneity of the cross-sectional liquid saturation, the application of the Kan-Liquid pre-wetting procedure outperforms the Levec pre-wetting procedure most probably due to the transition from rivulet to film flow texture.
The electrochemical experiments revealed that low maldistribution favor the liquid-solid mass transfer. Furthermore, the results indicated decreasing effective liquid–solid mass transfer coefficients from upper to lower part of the tubular reactor, which can be related to the worsening liquid distribution.
The extended results on the liquid distribution and liquid-solid mass transfer will be shown at with the whole paper.
Keywords: Catalysis; Chemical reactor; Foam; Hydrodynamics; Mass transfer
-
Lecture (Conference)
10th European Congress of Chemical Engineering, 27.09.-01.10.2015, Nice, France
Permalink: https://www.hzdr.de/publications/Publ-22870
Investigations on upward, downward and counter-current two-phase pipe flows using ultrafast electron beam X-ray computer tomography
Lucas, D.; Banowski, M.; Beyer, M.
Abstract
The ultra-fast electron beam X-ray computed tomography was developed during last years at HZDR and turned out to be a suitable measuring technique to get detailed information on the structure of gas-liquid interfaces. Air-water as well as steam-water experiments were done at a vertical pipe with an inner diameter of 54 mm and a test section length of about 4 m. They include co-current upward and downward flows under a wide variety of flow conditions and also some measurements for counter-current flows. In the latter case the bubble rise velocity was larger than the downward liquid velocity leading to an upward flow of bubbles and downward flow of water. Beside the tomographic reconstruction further data processing is required to obtain reliable quantitative data. A new algorithm for binarisation of the reconstructed data was developed.
The measurements were done with high frequency (between 1000 and 5000 frames per second depending on the flow conditions). In the result the instantaneous gas-liquid distributions in two horizontal planes with a distance of about 10 mm are obtained. Basing on that quantitative data like gas volume fraction distributions, average radial gas velocity profiles (basing on a cross-correlation between the two planes), bubbles size distributions and radial gas volume fraction profiles in dependence on the bubble size are obtained.
Since (in contrast to previously presented wire-mesh sensor measurements) the flow is not influenced by the measurement a bubble registered in the upstream plane can be assigned to the corresponding bubble in the downstream plane. This allows the determination of the velocity vector for each bubble. Special attention is paid to the dependency of lateral bubble velocities in dependence on the bubble sizes and the local flow conditions. Different effects are observed in upward and downward flows and will be discussed in detail.
Keywords: multiphase flow; tomography. experiment
Involved research facilities
- TOPFLOW Facility
-
Lecture (Conference)
7th European-Japanese Two-Phase Flow Group Meeting, 11.-15.10.2015, Zermatt, Switzerland
Permalink: https://www.hzdr.de/publications/Publ-22869
Qualification of CFD-models for multiphase flows
Lucas, D.
Abstract
While Computational Fluid Dynamics (CFD) is already an accepted industrial tool for single phase flows it is not yet mature for two-phase flows. For this reason the qualification of CFD for reactor safety relevant applications which involve multiphase flows is a present topic of research. At the CFD division of Helmholtz-Zentrum Dresden – Rossendorf (HZDR) hereby beside an application-oriented model development and validation also more generic investigations are done. Thus, the baseline model strategy aims on the consolidation of the CFD-modelling for multiphase to enable reliable predictions for well-defined flow pattern in future. In addition the recently developed GENTOP-concept broadens the range of applicability of CFD. Different flow morphologies including transitions between them can be considered in frame of this concept.
Keywords: CFD; multiphase flow
-
Kerntechnik 81(2016)2, 167-169
DOI: 10.3139/124.110686
Permalink: https://www.hzdr.de/publications/Publ-22868
Ultrafast dynamics in the charge-density-wave material CeTe3 across the pressure-induced phase transition
Tauch, J.; Schäfer, H.; Obergfell, M.; Demsar, J.; Giraldo, P.; Fisher, I. R.; Pashkin, A.
Abstract
Time-resolved optical spectroscopy is a powerful tool for studying ultrafast dynamics of quasiparticles and phonons in strongly correlated electronic systems. In particular, this technique has been efficiently utilized for investigation of charge-density-wave (CDW) compounds.1-3 In all these studies the system has been tuned across the boundary of the CDW phase by temperature variation. However, application of external (or chemical) pressure can also lead to a suppression of a CDW state caused by an impairment of the Fermi surface nesting.4
Here, we combine femtosecond time-resolved optical spectroscopy and a diamond anvil cell technology to study the electron and lattice dynamics in tri-telluride compound CeTe3. The optical pump-probe measurements (400 nm pump and 800 nm probe wavelength, respectively) are performed on single crystals mounted inside the pressure cell. CsI has been used as a pressure transmitting medium in order to ensure a contact between the sample and the diamond anvil.
Around pressures of 4 GPa we observe a gradual vanishing of the relaxation process related to the recombination of the photoexcited quasiparticles. The coherent oscillations of the phonon modes coupled to the CDW order parameter demonstrate even more dramatic suppression with increasing pressure. In addition, we observe an anomalous softening of a CDW amplitude mode. Our observations clearly indicate a transition into the metallic state of CeTe3 induced by the external pressure of about 4 GPa.
References
[1] J. Demsar et al., Phys. Rev. Lett. 83, 800 (1999).
[2] J. Demsar et al., Phys. Rev. B 66, 041101 (2002).
[3] R.V. Yusupov et al., Phys. Rev. Lett. 101, 246402 (2008).
[4] A. Sacchetti et al., Phys. Rev. Lett. 98, 026401 (2007).
Keywords: charge-density wave; ultrafast spectroscopy; high pressure; phase transition
-
Lecture (Conference)
Joint AIRAPT-25th & EHPRG-53rd International Conference on High Pressure Science and Technology, 30.08.-04.09.2015, Madrid, Spain
Permalink: https://www.hzdr.de/publications/Publ-22867
Ultrafast dynamics in CeTe3 near the pressure-induced charge-density-wave transition
Tauch, J.; Schäfer, H.; Obergfell, M.; Demsar, J.; Giraldo, P.; Fisher, I. R.; Pashkin, A.
Abstract
Femtosecond pump-probe spectroscopy is an efficient tool for studying ultrafast dynamics in strongly correlated electronic systems, in particular, compounds with a charge-density-wave (CDW) order. Application of external pressure often leads to a suppression of a CDW state due to an impairment of the Fermi surface nesting.
We combine time-resolved optical spectroscopy and diamond anvil cell technology to study electron and lattice dynamics in tri-telluride compound CeTe3. Around pressures of 4 GPa we observe a gradual vanishing of the relaxation process related to the recombination of the photoexcited quasiparticles. The coherent oscillations of the phonon modes coupled to the CDW order parameter demonstrate even more dramatic suppression with increasing pressure. These observations clearly indicate a transition into the metallic state of CeTe3 induced by the external pressure.
Keywords: Correlated Electrons; Nonequilibrium Quantum Many-Body Systems
-
Lecture (Conference)
DPG Spring Meeting 2015 (Berlin), 16.-20.03.2015, Berlin, Germany
Permalink: https://www.hzdr.de/publications/Publ-22866
Scalar fields in a non-commutative space
Bietenholz, W.; Hofheinz, F.; Mejía-Díaz, H.; Panero, M.
Abstract
We discuss the lambda phi(4) model in 2- and 3-dimensional non-commutative spaces. The mapping onto a Hermitian matrix model enables its non-perturbative investigation by Monte Carlo simulations. The numerical results reveal a phase where stripe patterns dominate. In d = 3 we show that in this phase the dispersion relation is deformed in the IR regime, in agreement with the property of UV/IR mixing. This "striped phase" also occurs in d = 2. For both dimensions we provide evidence that it persists in the simultaneous limit to the continuum and to infinite volume ("Double Scaling Limit"). This implies the spontaneous breaking of translation symmetry.
Involved research facilities
- PET-Center
-
Contribution to proceedings
XIV Mexican Workshop on Particles and Fields, 24.-29.11.2013, Oaxaca, Mexico
Journal of Physics Conference Series, Vol. 651, UNSP 01200
DOI: 10.1088/1742-6596/651/1/012003
Cited 4 times in Scopus
Permalink: https://www.hzdr.de/publications/Publ-22865
Identification of the Main Transition Velocities in a Bubble Column Based On a Modified Shannon Entropy
Nedeltchev, S.; Schubert, M.
Abstract
The gas holdup fluctuations in a bubble column (0.15 m in ID) have been recorded by means of a conductivity wire-mesh sensor in order to extract information about the main transition velocities. These parameters are very important for bubble column design, operation and scale-up. For this purpose, the classical definition of the Shannon entropy was modified and used to identify both the onset (at Ug=0.034 m/s) of the transition flow regime and the beginning (at Ug=0.089 m/s) of the churn-turbulent flow regime. The results were compared with the Kolmogorov entropy (KE) results. A slight discrepancy was found, namely the transition velocities identified by means of the KE were shifted to somewhat higher (0.045 and 0.101 m/s) superficial gas velocities Ug.
Keywords: Bubble column; Gas holdup fluctuations; Modified Shannon entropy; Kolmogorov entropy
Involved research facilities
- TOPFLOW Facility
-
Lecture (Conference)
18th International Conference on Chemical, Biochemical and Biomolecular Engineering (ICCBBE 2016), 25.-26.02.2016, London, United Kingdom -
International Journal of Chemical, Molecular, Nuclear, Materials and Metallurgical Engineering 10(2016)2, 214-217
Downloads
Permalink: https://www.hzdr.de/publications/Publ-22864
Numerical simulation of liquid metal batteries
Weber, N.; Galindo, V.; Kasprzyk, C.; Stefani, F.; Weier, T.
Abstract
Considering the increasing deployment of renewable energies, large-scale stationary energy storage will be a key-technology for the future. One potentially ideal grid-scale energy storage system is the liquid metal battery (LMB), consisting of a totally liquid interior. The long life time and abundant raw materials of LMBs offer a very cheap way of building batteries.
Building LMBs cheap means to make them large. Strong currents in the order of kA will drive a fluid flow, which may increase the battery's performance, or lead to a short circuit in the worst case.
A numerial model for describing the MHD fluid flow is presented and used to describe the Tayler instability, electro-vortex flow and interface instabilities in LMBs.
Keywords: simulation OpenFOAM liquid metal battery
-
Lecture (Conference)
10th PAMIR International Conference: Fundamental and Applied MHD, 20.-24.06.2016, Cagliari, Italien
Permalink: https://www.hzdr.de/publications/Publ-22863
Dynamic bias error correction in gamma-ray computed tomography
Wagner, M.; Bieberle, A.; Bieberle, M.; Hampel, U.
Abstract
The dynamic bias error is a well-known effect in transmission radiometry. It appears when an object distribution, e.g. a multiphase flow, changes its constitution during the scanning process and reconstructed data, e.g. a cross-sectional image, is assumed to represent a time-average of the object distribution. In gamma-ray tomography long sampling intervals are necessary in order to obtain sufficient photon count statistics. Therefore, the measured photon count projection data is inherently time-averaged. The attenuation law gives a non-linear relation between attenuation and photon counts. Therefore, the calculation of the time-averaged attenuation from the time-averaged projection data may lead to non-negligible and systematic errors, commonly an underestimation of the real attenuation, which e.g. means an overestimation of the gas holdup in tomography images of two-phase flows.
In this work the application of a recently presented dynamic bias error correction method on time-averaged gamma-ray tomography is demonstrated. As an exemplary object we scanned a mock-up of a centrifugal pump. The suitability of this method was investigated for a generic highly turbulent two-phase flow scenario with both a virtual tomography data set as well as real measured data.
Keywords: gamma-ray tomography; dynamic bias error; correct averaging
-
Flow Measurement and Instrumentation 53(2017), 141-146
Online First (2016) DOI: 10.1016/j.flowmeasinst.2016.10.012
Cited 6 times in Scopus
Permalink: https://www.hzdr.de/publications/Publ-22862
Hydrodynamic investigations of bubbly flow in periodic open cellular structures by ultrafast X-ray tomography
Wagner, M.; Zalucky, J.; Bieberle, M.; Hampel, U.
Abstract
Packed bubble columns are common multiphase flow reactor types in chemical engineering. Regarding process efficiency, high mass transfer rates are desirable. Especially, periodic open cell structures (POCS) are supposed to increase the interfacial density and hence the mass transfer in multiphase reactions. At the Helmholz-Zentrum Dresden – Rossendorf an ultrafast X-ray imaging technique is used to analyze a wide range of multiphase flow scenarios. A rotating electron beam induces X-ray generation on two targets which enables to produce up to 8000 cross-sectional images per second from two measurement planes with a spatial resolution of about 1 mm. We applied this tomography system in an experimental setup including POCS. In the threedimensional tomography data sets, bubbles were identified and characterized. For different gas flow rates, we determined the axial velocities of the gas-phase, bubble size distributions, bubble aspect ratios and timeaveraged gas hold-ups. We compared these results with measurements in an unpacked-bubble column. The results show that the POCS have a significant influence on the hydrodynamics, especially regarding the interfacial area density.
Keywords: ultrafast X-ray CT; two-phase flow; packed bubble column
-
Contribution to proceedings
10th Pacific Symposium on Flow Visualization and Image Processing, 15.-18.06.2015, Napoli, Italia -
Poster
10th Pacific Symposium on Flow Visualization and Image Processing, 15.-18.06.2015, Napoli, Italia
Permalink: https://www.hzdr.de/publications/Publ-22861
Requirements for a Compton camera for in-vivo range verification of proton therapy
Rohling, H.; Priegnitz, M.; Schöne, S.; Schumann, A.; Enghardt, W.; Hueso-Gonzalez, F.; Pausch, G.; Fiedler, F.
Abstract
To ensure the optimal outcome of proton therapy, in-vivo range verification is highly desired. Prompt gamma-ray imaging (PGI) is a possible approach for in-vivo range monitoring. For PGI dedicated detection systems, e.g. Compton cameras, are currently under investigation. The presented paper deals with substantial requirements regarding hardware and software that a Compton camera used in clinical routine has to meet. By means of GEANT4 simulations, we investigate the load on the detectors and the percentage of background expected in a realistic irradiation and we simulate gamma-ray detections, i.e. input data for the reconstruction. By reconstructing events from simulated sources of well-defined geometry, we show that large-area detectors are favourable. We determine the minimum number of valid events allowing for a statistically significant range assessment. Finally, an end-to-end test for a realistic patient scenario is presented: starting with a treatment plan, the gamma-ray emissions are calculated, the detector response is modelled, and the image reconstruction is performed. We conclude that, with respect to the achievable precision, the expected complexity, and high costs of an adequate detection system, in-vivo dosimetry with Compton cameras will hardly be realised.
Keywords: Prompt gamma-ray imaging; Compton camera; proton therapy; range verification; Monte Carlo simulation; end-to-end test; GEANT4
-
Physics in Medicine and Biology 62(2017)7, 2795-2811
DOI: 10.1088/1361-6560/aa6068
Cited 37 times in Scopus
Permalink: https://www.hzdr.de/publications/Publ-22860
The effect of pulsed electrical currents on the formation of macrosegregation in solidifying Al - Si hypoeutectic phases
Zhang, Y.; Räbiger, D.; Willers, B.; Eckert, S.
Abstract
Within this study we conducted experimental investigations focusing on the formation of macrosegregation in Al-7wt-%Si alloys exposed to electric current pulses (ECP) during solidification. The distribution of eutectic phase was measured on various sections of the solidified samples. The results do not show the formation of reproducible segregation pattern. This finding can be attributed to the specific pattern and the turbulent character of the flow generated by the ECP treatment, the equiaxed growth of free-moving crystals and a non-symmetric distribution of the electromagnetic force due to an uneven wetting of the electrodes. An increasing input of energy by ECP intensifies the melt flow and increases the variations of phase distribution over a longitudinal section.
Keywords: Al - Si alloys; solidification; electric current pulse; macrosegregation; melt convection
-
International Journal of Cast Metals Research 30(2017)1, 13-19
Online First (2016) DOI: 10.1080/13640461.2016.1174455
Cited 6 times in Scopus
Downloads
- Final Draft PDF 2,3 MB Secondary publication
Permalink: https://www.hzdr.de/publications/Publ-22859
Entropy Analysis in a Bubble Column Based On Ultrafast X-Ray Tomography Data
Nedeltchev, S.; Schubert, M.
Abstract
New ultrafast X-ray tomography data has been obtained in a bubble column (0.1 m in ID) operated with an air-deionized water system at ambient conditions. Raw reconstructed images were treated by both the information entropy (IE) and the reconstruction entropy (RE) algorithms in order to identify the main transition velocities in a bubble column. The IE values exhibited two well-pronounced minima at Ug=0.025 m/s and Ug=0.085 m/s identifying the boundaries of the homogeneous, transition and heterogeneous regimes. The reconstruction entropy extracted from the central region of the column’s cross-section exhibited only one characteristic peak at Ug=0.03 m/s, which was attributed to the transition from the homogeneous to the heterogeneous regime. This result implies that the transition regime is non-existent in the core of the column.
Keywords: Bubble column; Ultrafast X-ray tomography; Information entropy; Reconstruction entropy
Involved research facilities
- TOPFLOW Facility
-
Lecture (Conference)
18th International Conference on Chemical, Biochemical and Biomolecular Engineering, 25.-26.02.2016, London, UK -
International Journal of Chemical, Molecular, Nuclear, Materials and Metallurgical Engineering 10(2016)2, 256-259
Downloads
Permalink: https://www.hzdr.de/publications/Publ-22858
Prediction of Gas Holdups in Small and Large Bubble Columns Obtained from Advanced Imaging Techniques
Nedeltchev, S.; Schubert, M.; Hampel, U.
Abstract
The gas holdup is one of the most important parameters in the bubble column operation. Its successful prediction is important for the estimation of both the interfacial areas and the volumetric liquid-phase mass transfer coefficients. In the past several years, new imaging techniques for gas holdup measurements, such as the conductivity wire-mesh sensor as well as tomographic modalities have been used successfully for gas holdup measurements. Nedeltchev et al. (2014) have also shown that this data can be used for flow regime identification.
In this work, the gas holdup values were recorded in a small (0.15 m in ID) and a large (0.4 m in ID) bubble column equipped with perforated plate spargers (open area=1 %). A new model has been established, which predicts successfully the gas holdups in an air-deionized water system. It is based on both the theoretical and empirical evaluations of the gas-liquid interfacial areas. The correlation of Akita and Yoshida (1974) was assumed to be identical with the theoretical definition of the interfacial area. The Sauter-mean bubble diameters ds were estimated from the correlation of Wilkinson et al. (1994).
The theoretical gas holdups were corrected since the classical definition of the interfacial area is strictly valid for rigid spherical bubbles. All of our experimental conditions correspond to bubble diameters larger than 4.4×10-3 m, which means that the formed bubbles have an oblate ellipsoidal shape (Fan and Tsuchiya, 1990). It has been found that the common correction factor fc depends on both the bubble diameter (Eötvös number Eo) and the column diameter Dc (Bond number Bd). The effect of the column diameter (and Bond number) on the gas holdup should be carefully checked. As the superficial gas velocity Ug increased, the correction factors fc in the small column increased from 0.13 up to 0.25, whereas in the large column they increased from 1.33 to 2.55.
The approach is very useful since it predicts the gas holdups in the range 0.02 ≤ Ug ≤ 0.15 m/s irrespective of the prevailing flow regime. In the large column, the gas holdups were predicted with an average relative error (ARE) of 3.5 %, whereas in the small column ARE was 2.5 % (twelve gas holdup values in each column).
Keywords: Bubble Columns; Wire-Mesh Sensors; Gas Holdups; Prediction Model
Involved research facilities
- TOPFLOW Facility
-
Poster
Tenth European Congress of Chemical Engineering, 27.09.-01.10.2015, Nice, France
Permalink: https://www.hzdr.de/publications/Publ-22857
Different Identification Methods for Studying the Radial Distribution of the Transition Velocities in a Bubble Column
Nedeltchev, S.; Schubert, M.; Hampel, U.
Abstract
The identification of the boundaries of the main transition velocities in a bubble column is a very important research topic since it is related to the bubble column design and scale-up. The degrees of mixing, heat and mass transfer depend on the prevailing flow regime. In the literature hitherto, very different results (even for air-water system) about the main transition velocities Utrans have been reported. A good explanation for that is the fact that different signals (differential or absolute pressure fluctuations, bubble frequency, radioactive particle trajectories, photon counts, etc.) have been recorded and further analyzed by different methods (statistical analysis, fractal analysis, chaos analysis, etc.). The main objective of this work was to perform a comparison among the transition velocities (at different radial positions) identified by different entropies (information entropy, Kolmogorov entropy, Shannon entropy, etc.). The latter were extracted from gas holdup fluctuations recorded by a conductivity wire-mesh sensor. Recently, Nedeltchev et al. (2014) have shown that this data can be used for flow regime identification.
The data were recorded in a small (0.15 m in ID) bubble column equipped with a perforated plate gas distributor (14 holes, hole diameter: ø 4×10-3 m, open area=1 %). The local gas holdup fluctuations were measured at five different dimensionless radial positions (r/R): 0.88, 0.63, 0.39, 0.14 and 0.00. It was found that there were differences between the transition velocities identified by the information entropy (IE) and the Kolmogorov entropy (KE). The KE profile at r/R=0.88 was capable of identifying (based on a well-pronounced local minima) two Utrans values at 0.045 and 0.101 m/s. The IE profiles at the same radial position distinguished almost the same Utrans values: 0.045 and 0.112 m/s. The two transition velocities discriminate the boundaries of the three main flow regimes. Nedeltchev et al. (2014) visualized the flow patterns and documented the existence of strong gas maldistribution.
The KE profiles at r/R=0.63 revealed the existence of three Utrans values: 0.034, 0.067 and 0.124 m/s. In comparison with the wall region, at this radial position the transition regime was split into two sub-regimes. They were observed by Olmos et al. (2003). The IE profile at r/R=0.63 was difficult for interpretation due to the observed multiple local minima. However, taking into account the KE results the following three Utrans values were identified: 0.034, 0.067 and 0.112 m/s. So, only the last Utrans value was somewhat lower. Our results show that the transition is only a deviation (a sharp decrease) of a single point in the entropy profiles.
Such a detailed comparison between the IE and KE values was also performed at the other three radial positions. The IE values were derived from different initial information and compared with the Shannon entropies. Such a comparison has not been performed in the literature hitherto. We have found an effect of the radial position on the Utrans values.
Keywords: Bubble column; Wire-Mesh Sensor; Transition Velocities; Kolmogorov Entropy; Information Entropy
Involved research facilities
- TOPFLOW Facility
-
Lecture (Conference)
Tenth European Congress of Chemical Engineering, 27.09.-01.10.2015, Nice, France
Permalink: https://www.hzdr.de/publications/Publ-22856
Nanostructure, thermoelectric properties, and transport theory of V2VI3 and V2VI3 / IV-VI based superlattices and nanomaterials
Dankwort, T.; Hansen, A.-L.; Winkler, M.; Schürmann, U.; König, J. D.; Johnson, D. C.; Hinsche, N. F.; Zahn, P.; Mertig, I.; Bensch, W.; Kienle, L.
Abstract
The scope of this work is to review the thermoelectric properties, the microstructures, and their correlation with theoretical calculations and predictions for recent chalcogenide based materials. The main focus is put on thin multilayered Bi2Te3, Sb2Te3 films and bulk V2VI3/IV-VI mixed systems. For all films a systematic characterization of the thermoelectric properties as well as the micro- and nanostructure was performed. The degree of crystallinity of the multilayered films varied from epitaxial systems to polycrystalline films. Other multilayered thin films revealed promising thermoelectric properties. (SnSe)1.2TiSe2 thin films with rotational disorder yielded the highest Seebeck coefficient published to date for analogous materials. For bulk V2VI3/IV-VI mixed systems insides are given into a complete `material to module` process resulting in a high performance thermoelectric generator using (1-x)(GeTe) x(Bi2Se0.2Te2.8) (x = 0.038). Cyclic heating of this system with x = 0.063 resulted in a drastic change of the micro- and nanostructure observed by ex situ and in situ X-ray diffraction (XRD) and transmission electron microscopy (TEM). Consequently, a degradation of ZT at 450 °C from ~2.0 to ~1.0 was observed, while the less doped sample showed a stable ZT of 1.5.
Keywords: Bi2Te3/Sb2Te3 superlattice; thermoelectrics; Germanium Telluride; thin films; nanoalloying; electron microscopy
-
Physica Status Solidi (A) 213(2016)3, 662-671
DOI: 10.1002/pssa.201532471
Cited 14 times in Scopus
Permalink: https://www.hzdr.de/publications/Publ-22855
From prompt gamma distribution to dose: A novel approach combining an evolutionary algorithm and filtering based on gaussian-powerlaw convolutions
Schumann, A.; Priegnitz, M.; Schoene, S.; Enghardt, W.; Rohling, H.; Fiedler, F.
Abstract
Range verification and dose monitoring in proton therapy is considered as highly desirable. Different methods have been developed worldwide, like particle therapy positron emission tomography (PT-PET) and prompt gamma imaging (PGI). In general, these methods allow for a verification of the proton range. However, quantification of the dose from these measurements remains challenging. For the first time, we present an approach for estimating the dose from prompt gamma ray emission profiles. It combines a filtering procedure based on gaussian-powerlaw convolution with an evolutionary algorithm. By means of convolving depth dose profiles with an appropriate filter kernel, prompt gamma ray depth profiles are obtained. In order to reverse this step, the evolutionary algorithm is applied. The feasibility of this approach is demonstrated for a spread-out Bragg-peak in a water target.
Keywords: proton therapy; prompt gamma imaging; dose estimation; gaussian-powerlaw convolution; evolutionary algorithm; filter kernel
-
Physics in Medicine and Biology 61(2016)19, 6919-6934
DOI: 10.1088/0031-9155/61/19/6919
Cited 21 times in Scopus
Permalink: https://www.hzdr.de/publications/Publ-22854
Spatiotemporal image analysis of water flow in porous media for numerical transport modelling
Lippmann-Pipke, J.; Eichelbaum, S.; Kulenkampff, J.
Abstract
For more than a decade a spatiotemporal visualization tool for transport process observations in dense material by means of PET (positron emission tomography) was developed [1-5]. Such quantitative GeoPET images are exceptionally sensitive to displacements of pico molar tracer quantities detected within 1 mm grids on laboratory/drill core scale.
Now we reached a strategic milestone: A custom made image analysis algorithm is capable of quantitatively extracting velocity and porosity fields from such GeoPET image time series, even if the 4D image information includes discontinuous flow patterns (due to bottle neck effect related detection limits) and localized image artifacts. We present our approach with a concrete example: From an observed flow field in a dense core material the effective porosity and velocity field is extracted and this data is used in a finite element based transport simulation.
[1] Richter, M., et al. (2000) Z.angew.Geol. 46(2): 101-109.
[2] Gründig, M., et al. (2007) App.Geochem. 22: 2334-2343.
[3] Zakhnini, A., et al. (2013) Comp.Geosci. 57 183-196.
[4] Kulenkampff, J., et al. (2008) Phys.Chem.Earth 33: 937-942.
[5] Kulenkampff, J., et al. (2015) Clay Min. accepted 2015.
-
Lecture (Conference)
80. Jahrestagung der DPG und DPG-Frühjahrstagung, 06.-11.03.2016, Regensburg, Deutschland
Permalink: https://www.hzdr.de/publications/Publ-22853
Optical waveguides in Yb:SBN crystals fabricated by swift C ion irradiation
Liu, G.; Dong, N.; Wang, J.; Akhmadaliev, S.; Zhou, S.; Chen, F.
Abstract
We report on the fabrication of optical planar waveguides supporting both the TE and TM confinements in Yb:SBN crystal by swift C ions irradiation. A combination of the micro-photoluminescence and micro-Raman investigations have evidenced the presence of lattice distortion, damage and disordering of the SBN network along the ion irradiation path, with these effects being at the basis of the refractive index modification. The enhanced micro-photoluminescence and micro-Raman intensity in the waveguide volumes show the potential application of the obtained waveguides as active laser gain media.
Keywords: Optical waveguides; Yb:SBN crystal; Ion implantation; Confocal photoluminescence
Involved research facilities
- Ion Beam Center DOI: 10.17815/jlsrf-3-159
Related publications
- DOI: 10.17815/jlsrf-3-159 is cited by this (Id 22852) publication
-
Optical Materials 51(2016), 31-34
DOI: 10.1016/j.optmat.2015.11.019
Cited 2 times in Scopus
Permalink: https://www.hzdr.de/publications/Publ-22852
Optical ridge waveguides in Er3+/Yb3+ co-doped phosphate glass produced by ion irradiation combined with femtosecond laser ablation for guided-wave green and red upconversion emissions
Chen, C.; He, R.; Tan, Y.; Wang, B.; Akhmadaliev, S.; Zhou, S.; de Aldana, J. R. V.; Hu, L.; Chen, F.
Abstract
This work reports on the fabrication of ridge waveguides in Er3+/Yb3+ co-doped phosphate glass by the combination of femtosecond laser ablation and following swift carbon ion irradiation. The guiding properties of waveguides have been investigated at 633 and 1064 nm through end face coupling arrangement. The refractive index profile on the cross section of the waveguide has been constructed. The propagation losses can be reduced considerably after annealing treatment. Under the optical pump laser at 980 nm, the upconversion emission of both green and red fluorescence has been realized through the ridge waveguide structures.
Keywords: Ridge optical waveguides; Er3+/Yb3+ co-doped phosphate glass waveguides; Upconversion; Laser ablation; Ion irradiation
Involved research facilities
- Ion Beam Center DOI: 10.17815/jlsrf-3-159
Related publications
- DOI: 10.17815/jlsrf-3-159 is cited by this (Id 22851) publication
-
Optical Materials 51(2016), 185-189
DOI: 10.1016/j.optmat.2015.11.042
Cited 22 times in Scopus
Permalink: https://www.hzdr.de/publications/Publ-22851
Advances in radiotherapy special feature.
Krause, M.; Supiot, S.
-
British Journal of Radiology 88(2015)1051
DOI: 10.1259/bjr.20150412
Cited 3 times in Scopus
Permalink: https://www.hzdr.de/publications/Publ-22849
Comparison of [18F]-FMISO, [18F]-FAZA and [18F]-HX4 for PET imaging of hypoxia - a simulation study.
Wack, L. J.; Mönnich, D.; van Elmpt, W.; Zegers, C. M.; Troost, E. G.; Zips, D.; Thorwarth, D.
Abstract
BACKGROUND:
To investigate the effect of hypoxia tracer properties on positron emission tomography (PET) image quality for three tracers [18F]-fluoromisonidazole (FMISO), [18F]-fluoroazomycinarabinoside (FAZA) and [18F]-flortanidazole (HX4), using mathematical simulations based on microscopic tumor tissue sections.
MATERIAL AND METHODS:
Oxygen distribution and tracer binding was mathematically simulated on immunohistochemically stained cross-sections of tumor xenografts. Tracer diffusion properties were determined based on available literature. Blood activity and clearance over a four-hour period post-injection (p.i.) were derived from clinical dynamic PET scans of patients suffering from head and neck or bronchial cancer. Simulations were performed both for average patient blood activities and for individual patients, and image contrast between normoxic and hypoxic tissue areas was determined over this four-hour period p.i.
RESULTS:
On average, HX4 showed a six-fold higher clearance than FMISO and an almost three-fold higher clearance than FAZA based on the clinical PET data. The absolute variation in clearance was significantly higher for HX4 than for FMISO (standard deviations of 5.75 *10-5 s-1 vs. 1.55 *10-5 s-1). The absolute tracer activity in these scans at four hours p.i. was highest for FMISO and lowest for HX4. Simulated contrast at four hours p.i. was highest for HX4 (2.39), while FMISO and FAZA were comparable (1.67 and 1.75, respectively). Variations in contrast of 7-11% were observed for each tracer depending on the vascularization patterns of the chosen tissue. Higher variations in clearance for HX4 resulted in an increased inter-patient variance in simulated contrast at four hours p.i.
CONCLUSIONS:
In line with recent experimental and clinical data, the results suggest that HX4 is a promising new tracer that provides high image contrast four hours p.i., though inter-patient variance can be very high. Nevertheless, the widely used tracer FMISO provides a robust and reproducible signal four hours p.i., but with a lower contrast. The simulations revealed tracer clearance to be the key factor in determining image contrast.
-
Acta Oncologica 54(2015)9, 1370-1377
DOI: 10.3109/0284186X.2015.1067721
Cited 63 times in Scopus
Permalink: https://www.hzdr.de/publications/Publ-22848
Valproic acid modulates radiation-enhanced matrix metalloproteinase activity and invasion of breast cancer cells.
Artacho-Cordón, F.; Ríos-Arrabal, S.; Olivares-Urbano, M. A.; Storch, K.; Dickreuter, E.; Muñoz-Gámez, J. A.; León, J.; Calvente, I.; Torné, P.; Salinas, M. D.; Cordes, N.; Núñez, M. I.
Abstract
PURPOSE:
To evaluate matrix metalloproteinase (MMP) activity and invasion after ionizing radiation (IR) exposure and to determine whether MMP could be epigenetically modulated by histone deacetylase (HDAC) inhibition.
MATERIAL AND METHODS:
Two human breast cancer cell lines (MDA-MB-231 and MCF-7) were cultured in monolayer (2D) and in laminin-rich extracellular matrix (3D). Invasion capability, collagenolytic and gelatinolytic activity, MMP and TIMP protein and mRNA expression and clonogenic survival were analyzed after IR exposure, with and without a HDAC inhibition treatment [1.5 mM valproic acid (VA) or 1 μM trichostatin-A (TSA)].
RESULTS:
IR exposure resulted in cell line-dependent stimulation of invasion capacity. In contrast to MCF-7 cells, irradiated MDA-MB-231 showed significantly enhanced mRNA expression of mmp-1, mmp-3 and mmp-13 and of their regulators timp-1 and timp-2 relative to unirradiated controls. This translated into increased collagenolytic and gelatinolytic activity and could be reduced after valproic acid (VA) treatment. Additionally, VA also mitigated IR-enhanced mmp and timp mRNA expression as well as IR-increased invasion capability. Finally, our data confirm the radiosensitizing effect of VA.
CONCLUSION:
These results suggest that IR cell line-dependently induces upregulation of MMP mRNA expression, which appears to be mechanistically linked to a higher invasion capability that is modifiable by HDAC inhibition.
Keywords: Matrix metalloproteinases; breast cancer; epigenetic regulation; histone deacetylases; invasion; ionizing radiation; tumour microenvironment
-
International Journal of Radiation Biology 91(2015)12, 946-956
DOI: 10.3109/09553002.2015.1087067
Cited 10 times in Scopus
Permalink: https://www.hzdr.de/publications/Publ-22847
ILKAP, ILK and PINCH1 control cell survival of p53-wildtype glioblastoma cells after irradiation.
Hausmann, C.; Temme, A.; Cordes, N.; Eke, I.
Abstract
The prognosis is generally poor for patients suffering from glioblastoma multiforme (GBM) due to radiation and drug resistance. Prosurvival signaling originating from focal adhesion hubs essentially contributes to therapy resistance and tumor aggressiveness. As the underlying molecular mechanisms remain largely elusive, we addressed whether targeting of the focal adhesion proteins particularly interesting new cysteine-histidine-rich 1 (PINCH1), integrin-linked kinase (ILK) and ILK associated phosphatase (ILKAP) modulates GBM cell radioresistance. Intriguingly, PINCH1, ILK and ILKAP depletion sensitized p53-wildtype, but not p53-mutant, GBM cells to radiotherapy. Concomitantly, these cells showed inactivated Glycogen synthase kinase-3β (GSK3β) and reduced proliferation. For PINCH1 and ILKAP knockdown, elevated levels of radiation-induced γH2AX/53BP1-positive foci, as a marker for DNA double strand breaks, were observed. Mechanistically, we identified radiation-induced phosphorylation of DNA protein kinase (DNAPK), an important DNA repair protein, to be dependent on ILKAP. This interaction was fundamental to radiation survival of p53-wildtype GBM cells. Conclusively, our data suggest an essential role of PINCH1, ILK and ILKAP for the radioresistance of p53-wildtype GBM cells and provide evidence for DNAPK functioning as a central mediator of ILKAP signaling. Strategies for targeting focal adhesion proteins in combination with radiotherapy might be a promising approach for patients with GBM.
Keywords: DNA repair; ILK; ILKAP; PINCH1; radioresistance
-
Oncotarget 6(2015)33, 34592-34605
DOI: 10.18632/oncotarget.5423
Cited 14 times in Scopus
Permalink: https://www.hzdr.de/publications/Publ-22846
Abschätzung des Sekundärneutronenfeldes bei der Protonentherapie mit passiv geformten Feldern
Lutz, B.; Enghardt, W.; Swanson, R.; Fiedler, F.
Abstract
Die Strahlentherapie mit Protonen erlaubt, im Vergleich zur Bestrahlung mit Photonen, eine stärkere Lokalisierung der durch die primäre Strahlung verabreichten Dosis im Tumor. Die damit verbundene Schonung gesunden Gewebes ist der größte Vorteil dieser Form der Strahlentherapie.
Die verbleibende Belastung des gesunden Gewebes wird hauptsächlich durch sekundäre Neutronen verursacht. Der Fluss und das Spektrum der sekundären Neutronen hängen dabei stark von der gewählten Konfiguration der Therapieanlage ab.
Um das Sekundärneutronenfeld an der Protonentherapieanlage des Universitätsklinikum Carl Gustav Carus in Dresden abschätzen zu können, wird eine detaillierte Simulation der Strahlformung mit Hilfe der Software TOPAS entwickelt. Der Vortrag beschreibt die Implementation der Anlage und die erwarteten Neutronenspektren. Der Einfluß verschiedener Maschinenparameter auf das Neutronenfeld wird diskutiert. Abschließend wird die Vorhersage mit ersten Messungen der Ortsdosis am Therapieplatz verglichen.
-
Lecture (Conference)
DPG-Frühjahrstagung der Sektion Materie und Kosmos (SMuK), 29.02.-04.03.2016, Hamburg, Deutschland
Permalink: https://www.hzdr.de/publications/Publ-22845
On the use of HERFD-XANES at the U L3 and M4-edges to determine the uranium valence state on [Ni(H2O)4]3[U(OH,H2O)(UO2)8O12(OH)3]
Bès, R.; Rivenet, M.; Solari, P. L.; Kvashnina, K. O.; Scheinost, A. C.; Martin, P. M.
Abstract
We report and discuss here the unambiguous uranium valence state determination on the complex compound [Ni(H2O)4]3[U(OH,H2O)(UO2)8O12(OH)3] by using High Energy Resolution Fluorescence Detection - X-ray Absorption Near Edge Structure spectroscopy (HERFD-XANES). The spectra at both uranium L3- and M4-edges confirm that all the five non-equivalent uranium atoms are solely in the hexavalent form in this compound, as previously suggested by Bond Valence Sum analysis and X-ray diffraction pattern refinement. Moreover, the presence of the pre-edge feature, due to the 2p3/2-5f quadrupole transition, has been observed in the U L3-edge HERFD-XANES spectrum, in agreement with theoretical and experimental observations of other uranium based compounds. Recently, this feature has been proposed as a possible tool to determine the uranium oxidation state in a manner similar to 3d and 4d metals. Nevertheless, this feature is also very sensitive to the uranium local environment, as revealed by our theoretical calculations, and consequently could not be used to attribute without ambiguity the uranium valence state. In contrast, U M4-edge HERFD-XANES appears to be the most straightforward and reliable way to assess uranium valence state in very complex materials such as [Ni(H2O)4]3[U(OH,H2O)(UO2)8O12(OH)3] or mixture of compounds.
Keywords: XANES; XES; HERFD; uranium oxidation state
Involved research facilities
- Rossendorf Beamline at ESRF DOI: 10.1107/S1600577520014265
Related publications
- DOI: 10.1107/S1600577520014265 is cited by this (Id 22844) publication
-
Inorganic Chemistry 55(2016), 4260-4270
DOI: 10.1021/acs.inorgchem.6b00014
Cited 41 times in Scopus
Permalink: https://www.hzdr.de/publications/Publ-22844
Pulsed-Magnet Developments at the Dresden High Magnetic Field Laboratory
Zherlitsyn, S.; Herrmannsdörfer, T.; Wosnitza, J.
Involved research facilities
- High Magnetic Field Laboratory (HLD)
-
Lecture (Conference)
MT24 - International Conference on Magnet Technology 24, 18.-23.10.2015, Seoul, Korea
Permalink: https://www.hzdr.de/publications/Publ-22843
Magneto-Acoustic Studies of Frustrated Quantum Magnets
Pham, T.-C.
Involved research facilities
- High Magnetic Field Laboratory (HLD)
-
Invited lecture (Conferences)
International Symposium on Frontiers in Materials Science 2015, 19.-21.11.2015, Tokyo, Japan
Permalink: https://www.hzdr.de/publications/Publ-22842
The gas chromatographic analysis of the reaction products of the partial isobutane oxidation as a two phase process.
Willms, T.; Kryk, H.; Hampel, U.
Abstract
The partial oxidation of isobutane to t-butyl hydroperoxide (TBHP) has been studied analytically for the first time as a two-phase process in a capillary micro reactor. In order to obtain detailed information on products, yields, selectivity and reaction pathways, the products have been investigated by GC/MS. An Rxi-5ms column and a PTV-injector have been used to analyze the liquid products. TBHP, di-t-butyl peroxide (DTBP), t-butanol (TBA), and propanone as main products as well as further by-products e.g. methanal, isopropanol, isobutanol and isobutanal in minor quantities have been identified by MS. The liquid products have been obtained by quenching the reaction and vaporizing the isobutane afterwards by pressure reduction using a mass flow controller allowing a constant mass flow. For all liquid reaction products calibrations, a validation of the method including limits of quantification and detection as well as calculation of uncertainties has been performed. The results have been applied successfully for the investigation of the selectivities of the main products (TBHP, DTBP, TBA, propanone) of the isobutane oxidation. In the frame of the analytical investigation of this reaction a correlation coefficient of r2 > 0.999 for TBHP and DTBP, which is necessary to perform a validation, has been obtained for the first time. The gaseous phase has been analyzed using a GASPRO Column, a DEANS switch, a mole sieve column and a TCD detector. Apart from the gaseous reactants, isobutene has been found.
Keywords: Isobutane oxidation; t-butyl hydroperoxide; di-t-butyl-peroxide; GC/MS; multiphase process
-
Journal of Chromatography A 1458(2016), 126-135
DOI: 10.1016/j.chroma.2016.06.052
Cited 9 times in Scopus
Downloads
- Final Draft PDF 520 kB Secondary publication
Permalink: https://www.hzdr.de/publications/Publ-22840
Flüssig-Flüssig-Extraktion von Seltenen Erden mit Hilfe von Calix[4]arenen
Mansel, A.
-
Lecture (others)
1. Verbundtreffen zum BMBF/PtJ-Projekt "SE-FLECX" an der Universität Leipzig, Institut für Anorganische Chemie, 26.11.2015, Leipzig, Deutschland
Permalink: https://www.hzdr.de/publications/Publ-22839
How Details of the Geometallurgical Optimisation Influence Overall Value
van den Boogaart, K. G.; Tolosana Delgado, R.; Müller, U.; Matos Camacho, S.
Abstract
The precise formulation of a geometallurgical optimisation problem is by necessity a simplification of reality. It includes implicit choices such as data availability or mining block geometry. Additional data can be ore body data, production data or market data. Often these choices are predetermined by the software, the workflow or corporate culture and as such are not even queried. There are several aspects that might play a role in the optimization. They include not only the spatial model on which the selection of mining blocks and the potential mining sequence are based, but also the complexity of the processing model, the way in which uncertainty is treated, the scope of responsibility and the complexity of the model. In addition the timing of the optimization and the availability (or lack thereof) of information influence the outcome of any optimization.
We show that different modelling choices and different model formulations for the same mine can lead to very different processing choices, substantially different NPV’s , opposite investment decisions and so to overall different values for the entire operation. The selection of adequate simplifications and corresponding formulations for the optimisation problem is thus an important task in itself.
For this purpose we introduce a method quantifying the impact of certain simplifications prior to the optimization itself. E.g. for the effect of mining block choices the effect depends mainly on the spatial structure and the structure of the processing gain function. Both can be quantified beforehand. Likewise the effect of additional data depend on the increase of information. Again this can be quantified from a spatial model.
Based on the outcome appropriate simplifications can be selected for the geometallurgical optimization.
Keywords: geometallurgy; model choice; adaptive processing
-
Contribution to proceedings
GeoMet 2016, The third AusIMM International Geometallurgy Conference, 15.-17.06.2016, Perth, Australia
Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, Melbourn: The Australasian Institute of Mining and Metallurg, 303-312 -
Lecture (Conference)
GeoMet 2016, The third AusIMM International Geometallurgy Conference, 15.-17.06.2016, Perth, Australia
Permalink: https://www.hzdr.de/publications/Publ-22838
Time-Resolved Two Million Year Old Supernova Activity Discovered in the Earth’s Microfossil Record
Ludwig, P.; Bishop, S.; Egli, R.; Chernenko, V.; Deneva, B.; Faestermann, T.; Famulok, N.; Fimiani, L.; Gómez-Guzmán, J.; Hain, K.; Korschinek, G.; Hanzlik, M.; Merchel, S.; Rugel, G.
Abstract
Massive (>10M_⊙) stars, which terminate their evolution as core collapse supernovae (CCSN), are theoretically predicted 1 to eject >10-5M_⊙ of the radioactive isotope 60Fe (half-life t1/2=(2.61±0.04) Ma; weighted average of Ref. 2 and 3). If such an event occurs sufficiently close to our solar system, one expects that traces of the supernova (SN) debris could be deposited on Earth. Since 60Fe has no or little expected anthropogenic or cosmogenic production mechanisms, its detection in terrestrial reservoirs would be an immediate proxy for a past Earth-SN interaction within the past few million years. Herein, we report for the first time a time-resolved 60Fe signal residing, at least partially, in a biogenic reservoir. Using the experimental technique of accelerator mass spectrometry (AMS), this signal was found through the direct detection of live 60Fe atoms contained within secondary Fe-oxides, among which are magnetofossils 4; the fossilized chains of magnetite crystals produced by magnetotactic bacteria 5, 6. Magnetofossil preservation precludes post-depositional Fe mobilization events, ensuring that the 60Fe record is correctly preserved. The magnetofossils were chemically extracted from two Pacific Ocean sediment drill cores. Our results show that the 60Fe signal onset occurs around 2.7 Ma, near the lower Pleistocene boundary, terminates between 1.4 Ma and 1.8 Ma, and peaks at about 2.2 Ma.
Keywords: accelerator mass spectrometry; AMS; supernova; cosmogenic nuclide
Involved research facilities
- Ion Beam Center DOI: 10.17815/jlsrf-3-159
Related publications
- DOI: 10.17815/jlsrf-3-159 is cited by this (Id 22837) publication
-
Proceedings of the National Academy of Sciences of the United States of America 113(2016)33, 9232-9237
DOI: 10.1073/pnas.1601040113
Cited 66 times in Scopus
Permalink: https://www.hzdr.de/publications/Publ-22837
On the Lorentz-force driven flow around an insulating sphere
Massing, J.; Baczyzmalski, D.; Weier, T.; Landgraf, S.; Cierpka, C.
Abstract
The Lorentz-force driven flow around an insulating sphere in a parallel electric and magnetic field was investigated experimentally and numerically. From the results, the lift force acting on the bubble due to the pressure reduction caused by the Lorentz-force driven flow was estimated, which was discussed in the literature as the primary cause for a faster bubble detachment in a parallel magnetic field. It could be shown, that the pressure force is several orders of magnitudes smaller than the buoyancy force and therefore has no significant effect on the bubble detachment. This finding is supported by the measurement results of the 3D3C velocity field around an elevated, axially magnetized sphere in an electric field. In the final paper the 3D3C flow around the bubble will be analyzed in greater detail and hydrodynamic mechanisms to explain the faster detachment will be further discussed.
Keywords: Lorentz force; electrolysis; Astigmatism Particle Tracking Velocimetry
-
Lecture (Conference)
18th Lisbon International Symposium on Applications of Laser and Imaging Techniques to Fluid Mechanics, 04.-07.07.2016, Lissabon, Portugal -
Contribution to proceedings
18th Lisbon International Symposium on Applications of Laser and Imaging Techniques to Fluid Mechanics, 04.-07.07.2016, Lissabon, Portugal, 978-989-98777-8-8
Permalink: https://www.hzdr.de/publications/Publ-22836
Sodium-bismuth-lead low temperature liquid metal battery
Lalau, C.-C.; Ispas, A.; Weier, T.; Bund, A.
Abstract
The development of a low temperature liquid metal battery based on ionic liquids namely, sodium-bis(trifluoromethylsulfonyl) imide (Na[TFSI]) in tetraethylammonium-bis(trifluoromethylsulfonyl) imide ([TEA][TFSI]) will be discussed. Such a battery should be easily accessible for fluid flow measurements which is still a challenge with the conventional high temperature systems. Cells comprising a Na negative electrode, 20 mole % Na[TFSI] in [TEA][TFSI] ionic liquid electrolyte and a Pb-Bi eutectic positive electrode were constructed and operated at 160 °C. Galvanostatic cycling experiments were conducted at low C rates (C/26) for 13 h corresponding to 50 % depth of discharge. A discharge capacity of 565 mAh/g was found. Furthermore electrochemical impedance spectroscopy was used to characterize the aging of the cells.
Keywords: Liquid metal batteries; Ionic liquids; Sodium; Electrochemical impedance spectroscopy; Storage
-
Journal for Electrochemistry and Plating Technology (2015), JEPT4808
DOI: 10.12850/ISSN2196-0267.JEPT4808
ISSN: 2196-0267
Permalink: https://www.hzdr.de/publications/Publ-22835
Strange meson production in Al+Al collisions at 1.9 A GeV
Gasik, P.; Piasecki, K.; Herrmann, N.; Leifels, Y.; Matulewicz, T.; Andronic, A.; Averbeck, R.; Barret, V.; Basrak, Z.; Bastid, N.; Benabderrahmane, M. L.; Berger, M.; Buehler, P.; Cargnelli, M.; Caplar, R.; Crochet, P.; Czerwiakowa, O.; Deppner, I.; Dupieux, P.; Dzelalija, M.; Fabbietti, L.; Fodor, Z.; Gasparic, I.; Grishkin, Y.; Hartmann, O. N.; Hildenbrand, K. D.; Hong, B.; Kang, T. I.; Kecskemeti, J.; Kim, Y. J.; Kirejczyk, M.; Kis, M.; Koczon, P.; Kotte, R.; Lebedev, A.; Le Fevre, A.; Liu, J. L.; Lopez, X.; Manko, V.; Marton, J.; Münzer, R.; Petrovici, M.; Rami, F.; Reischl, A.; Reisdorf, W.; Ryu, M. S.; Schmidt, P.; Schüttauf, A.; Seres, Z.; Sikora, B.; Sim, K. S.; Simion, V.; Siwek-Wilczynska, K.; Smolyankin, V.; Suzuki, K.; Tyminski, Z.; Wagner, P.; Weber, I.; Widmann, E.; Wisniewski, K.; Xiao, Z. G.; Yushmanov, I.; Zhang, Y.; Zhilin, A.; Zinyuk, V.; Zmeskal, J.
Abstract
The production of K+, K- and φ(1020) mesons are studied in Al+Al collisions at beam energy of 1.9A GeV which is close or below the production threshold in NN reactions. Inverse slopes, anisotropy parameters, and total emission yields of K± mesons are obtained. A comparison of the ratio of kinetic energy distributions of K- and K+ mesons to transport model calculations (IQMD and HSD) suggests that the inclusion of in-medium modifications of kaon properties is necessary to reproduce the ratio. The inverse slope and total yield of φ mesons are deduced. The contribution to K- production from φ meson decays is found to be 17 ± 3%. The results are in line with previous K± and φ data obtained for different colliding systems at similar incident beam energies.
-
European Physical Journal A 52(2016), 177
DOI: 10.1140/epja/i2016-16177-y
Cited 13 times in Scopus -
Contribution to WWW
arXiv:1512.06988: https://arxiv.org/abs/1512.06988
Downloads
- Final Draft PDF 369 kB Secondary publication
Permalink: https://www.hzdr.de/publications/Publ-22834
Abschirmungs- und Aktivierungsberechnungen für den MYRRHA-Forschungsreaktor in Mol
Ferrari, A.; Konheiser, J.; Mueller, S. E.
-
Lecture (Conference)
15. AAA Workshop, 07.12.2015, Garching, Germany
Permalink: https://www.hzdr.de/publications/Publ-22833
AER Working Group D on VVER Safety Analysis – Report of the 2015 Meeting
Kliem, S.
Abstract
The AER Working Group D on VVER reactor safety analysis held its 24th meeting in Madrid, Spain, during the period 18-19 May, 2015. The meeting was hosted by UPM Madrid and was held in conjunction with the ninth workshop on the OECD Benchmark for Uncertainty Analysis in Best-Estimate Modelling (UAM) for Design, Operation and Safety Analysis of LWRs. Altogether 19 participants attended the meeting of the working group D, 17 from AER member organizations and 2 guests from non-member organization. The co-ordinator of the working group, Mr. S. Kliem, served as chairman of the meeting. The meeting started with a general information exchange about the recent activities in the participating organizations.
The given presentations and the discussions can be attributed to the following topics:
- Safety analyses methods and results
- Code development and benchmarking including the calculation of the OECD/NEA Benchmark for the Kalinin-3 VVER-1000 NPP and 7th AER Dynamic Benchmark
- Thermal hydraulic analyses of fuel assemblies
- Future activities
-
Contribution to proceedings
25th Symposium of AER on VVER Reactor Physics and Reactor Safety, 13.-16.10.2015, Balatongyörök, Hungary
Proceedings of the 25th Symposium of AER on VVER Reactor Physics and Reactor Safety, Budapest: MTA EK, 9789637351259, 247-253 -
Lecture (Conference)
25th Symposium of AER on VVER Reactor Physics and Reactor Safety, 13.-16.10.2015, Balatongyörök, Hungary
Permalink: https://www.hzdr.de/publications/Publ-22832
Band-gap narrowing in Mn-doped GaAs probed by room-temperature photoluminescence
Prucnal, S.; Gao, K.; Skorupa, I.; Rebohle, L.; Vines, L.; Schmidt, H.; Khalid, M.; Wang, Y.; Weschke, E.; Skorupa, W.; Grenzer, J.; Hübner, R.; Helm, M.; Zhou, S.
Abstract
The electronic band structure of the (Ga,Mn)As system has been one of the most intriguing problems in solid state physics over the past two decades. Determination of the band structure evolution with increasing Mn concentration is a key issue to understand the origin of ferromagnetism. Here, we present room-temperature photoluminescence and ellipsometry measurements of Ga100%−xMnxAs alloy. The upshift of the valence band is proven by the redshift of the room temperature near band-gap emission from the Ga100%−xMnxAs alloy with increasingMn content. It is shown that even a doping by 0.02% of Mn affects the valence-band edge, and it merges with the impurity band for a Mn concentration as low as 0.6%. Both x-ray diffraction pattern and high-resolution cross-sectional transmission electron microscopy images confirmed full recrystallization of the implanted layer and GaMnAs alloy formation.
Keywords: diluted magnetic semiconductors; (Ga; Mn)As; ion implantation; flash lamp annealing
Involved research facilities
- Ion Beam Center DOI: 10.17815/jlsrf-3-159
Related publications
- DOI: 10.17815/jlsrf-3-159 is cited by this (Id 22831) publication
-
Physical Review B 92(2015), 224407
DOI: 10.1103/PhysRevB.92.224407
Cited 11 times in Scopus
Permalink: https://www.hzdr.de/publications/Publ-22831
YMnO3- based MIS structure with a selective, capacitive photo-detecting properties
Bogusz, A.; Choudhary, O. S.; Skorupa, I.; Bürger, D.; Lawerenz, A.; Schmidt, O. G.; Schmidt, H.
Abstract
This work investigates the YMnO3/Si3N4 /p-Si structures in terms of novel, capacitance-based photo-detecting properties. Photocapacitance-voltage (C-V) characteristics of the YMnO3/Si3N4 /p-Si structures have been determined at room temperature for a wide spectral range (300-980 nm). C-V characteristics indicate a charge trapping process which is used as the basis for novel approach to photodetectors. Our model discusses the immobilization of otherwise mobile charges in Si3N4 when the negative polarization charge of the multiferroic YMnO3 is at the YMnO3/Si3N4 interface. The observed capacitance minima are well-defined by the direction of bias ramp. Voltages corresponding to these minima were further used as a reference point for a read out of capacitance in retention and optical selectivity tests. Results indicate that investigated structures exhibit a good photo-sensitivity of red light and the retention properties are non-volatile for one capacitance branch.
-
Lecture (Conference)
DPG Spring Meeting 2015, 15.-20.03.2015, Berlin, Germany
Permalink: https://www.hzdr.de/publications/Publ-22830
Resistive switching of polycrystalline, multiferroic YMnO3 thin films
Bogusz, A.; Prucnal, S.; Blaschke, D.; Skorupa, I.; Bürger, D.; Schmidt, O. G.; Schmidt, H.
Abstract
Resistive switching (RS) phenomena have been widely investigated in the field of materials science, physics, and electrical engineering in the past decade. Recently, multiferroics have been considered as promising candidates for memristive switches. Specific properties of multiferroics might bring additional and/or new functionalities into the memristive switches. This work investigates the RS properties of multiferroic YMnO3 thin films reported as a unipolar resistive switches. YMnO3 was grown at 400°C on Pt/Ti/SiO2/Si substrates by pulsed laser deposition (PLD) and crystallized by flash lamp annealing (FLA). Film thickness and the concentration of point defects were controlled during the PLD process. Transport and Rs properties of Au/YMnO3/Pt/Ti/SiO2 structures were determined by two-point probe measurements in a top-bottom configuration. Results imply that the filamentary, unipolar RS in YMnO3 originates from the electro-redox reactions induced by the Joule heating.
-
Lecture (Conference)
DPG Spring Meeting, 15.-20.03.2015, Berlin, Germany
Permalink: https://www.hzdr.de/publications/Publ-22829
Interaction of europium and curium with alpha-amylase
Barkleit, A.; Heller, A.; Ikeda-Ohno, A.; Bernhard, G.
Abstract
The complexation of Eu(III) and Cm(III) with the protein α-amylase (Amy), a major enzyme in saliva and pancreatic juice, was investigated over wide ranges of pH and concentration at both ambient and physiological temperatures. Macroscopic sorption experiments demonstrated a strong and fast binding of Eu(III) to Amy between pH 5 and 8. The protein provides three independent, non-cooperative binding sites for Eu(III). The overall association constant of these three binding sites on the protein was calculated to be log K = 6.4 ± 0.1 at ambient temperature. With potentiometric titration the averaged deprotonation constant of the carboxyl groups (the aspartic and glutamic acid residues) of Amy was determined to be pKa = 5.23 ± 0.14 at 25 °C and 5.11 ± 0.24 at 37 °C. Time-resolved laser-induced fluorescence spectroscopy (TRLFS) revealed two different species for both Eu(III) and Cm(III) with Amy. In the case of the Eu(III) species, the stability constants were determined to be log β11 = 4.7 ± 0.2 and log β13 = 12.0 ± 0.4 for Eu:Amy = 1:1 and 1:3 complexes, respectively, while the values for the respective Cm(III) species were log β11 = 4.8 ± 0.1 and log β13 = 12.1 ± 0.1. Furthermore, the obtained stability constants were extrapolated to infinite dilution to make our data compatible with the existing thermodynamic database.
-
Dalton Transactions 45(2016)21, 8724-8733
DOI: 10.1039/C5DT04790K
Cited 21 times in Scopus
Permalink: https://www.hzdr.de/publications/Publ-22828
First tests of the prompt gamma ray timing method at a clinical proton accelerator
Hueso-González, F.; Golnik, C.; Berthel, M.; Dreyer, A.; Enghardt, W.; Fiedler, F.; Janssens, G.; Kormoll, T.; Petzoldt, J.; Prieels, D.; Priegnitz, M.; Römer, K. E.; Smeets, J.; Sobiella, M.; Vander Stappen, F.; Wagner, A.; Weinberger, D.; Pausch, G.
Abstract
The characteristic dose profile of accelerated ions has opened up new horizons in the context of cancer treatment. However, particle range uncertainties strongly constrain the potentialities of ion beam therapy. Despite of worldwide efforts, a detector system for range and dose delivery assessment in real-time is not yet available for clinical routine.
Complementary to the active- and passively collimated prompt gamma ray imaging systems for range assessment, the prompt gamma ray timing method has been recently proposed and tested at a research accelerator. Based on the measurable transit time of ions through matter, the emission times of prompt gamma rays encode essential information about the depth-dose profile.
In a collaboration between OncoRay, Helmholtz-Zentrum Dresden-Rossendorf and IBA, the prompt gamma ray timing method was tested for the first time at a clinical proton accelerator (Westdeutsches Protonentherapiezentrum Essen) with different phantoms. Several fast scintillation detectors were used to acquire prompt gamma ray timing distributions at various geometries and proton energies.
From the resulting distributions, particle range differences of around 5 millimetres in heterogeneous phantoms were observed by simple qualitative inspection. In conclusion, our preliminary analysis points out that the prompt gamma ray timing method for range verification is feasible in a clinical radiation environment and realistic phantoms, which reassures this novel approach as a promising alternative in the field of prompt gamma based in vivo dosimetry.
Keywords: prompt gamma-ray timing; proton therapy; range verification; in vivo dosimetry
-
Contribution to proceedings
Workshop on Range Assessment and Dose Verification in Particle Therapy, 29.-30.09.2014, Dresden, Germany
Permalink: https://www.hzdr.de/publications/Publ-22827
Years: 2023 2022 2021 2020 2019 2018 2017 2016 2015
Pages: [1.] [2.] [3.] [4.] [5.] [6.] [7.] [8.] [9.] [10.] [11.] [12.] [13.] [14.] [15.] [16.] [17.] [18.] [19.] [20.] [21.] [22.] [23.] [24.] [25.] [26.] [27.] [28.] [29.] [30.] [31.] [32.] [33.] [34.] [35.] [36.] [37.] [38.] [39.] [40.] [41.] [42.] [43.] [44.] [45.] [46.] [47.] [48.] [49.] [50.] [51.] [52.] [53.] [54.] [55.] [56.] [57.] [58.] [59.] [60.] [61.] [62.] [63.] [64.] [65.] [66.] [67.] [68.] [69.] [70.] [71.] [72.] [73.] [74.] [75.] [76.] [77.] [78.] [79.] [80.] [81.] [82.] [83.] [84.] [85.] [86.] [87.] [88.] [89.] [90.] [91.] [92.] [93.] [94.] [95.] [96.] [97.] [98.] [99.] [100.] [101.] [102.] [103.] [104.] [105.] [106.] [107.] [108.] [109.] [110.] [111.] [112.] [113.] [114.] [115.] [116.] [117.] [118.] [119.] [120.] [121.] [122.] [123.] [124.] [125.] [126.] [127.] [128.] [129.] [130.] [131.] [132.] [133.] [134.] [135.] [136.] [137.] [138.] [139.] [140.] [141.] [142.] [143.] [144.] [145.] [146.] [147.] [148.] [149.] [150.] [151.] [152.] [153.] [154.] [155.] [156.] [157.] [158.] [159.] [160.] [161.] [162.] [163.] [164.] [165.] [166.] [167.] [168.] [169.] [170.] [171.] [172.] [173.] [174.] [175.] [176.] [177.] [178.] [179.] [180.] [181.] [182.] [183.] [184.] [185.] [186.] [187.] [188.] [189.] [190.] [191.] [192.] [193.] [194.] [195.] [196.] [197.] [198.] [199.] [200.] [201.] [202.] [203.] [204.] [205.] [206.] [207.] [208.] [209.] [210.] [211.] [212.] [213.] [214.] [215.] [216.] [217.] [218.] [219.] [220.] [221.] [222.] [223.] [224.] [225.] [226.] [227.] [228.] [229.] [230.] [231.] [232.] [233.] [234.] [235.] [236.] [237.] [238.] [239.] [240.] [241.] [242.] [243.] [244.] [245.] [246.] [247.] [248.] [249.] [250.] [251.] [252.] [253.] [254.] [255.] [256.] [257.] [258.] [259.] [260.] [261.] [262.] [263.] [264.] [265.] [266.] [267.] [268.] [269.] [270.] [271.] [272.] [273.] [274.] [275.] [276.] [277.] [278.] [279.] [280.] [281.] [282.] [283.] [284.] [285.] [286.] [287.] [288.] [289.] [290.] [291.] [292.] [293.] [294.] [295.] [296.] [297.] [298.] [299.] [300.] [301.] [302.] [303.] [304.] [305.] [306.] [307.] [308.] [309.] [310.] [311.] [312.] [313.] [314.] [315.] [316.] [317.] [318.] [319.] [320.] [321.] [322.] [323.] [324.] [325.] [326.] [327.] [328.] [329.] [330.] [331.] [332.] [333.] [334.] [335.] [336.] [337.] [338.] [339.] [340.] [341.] [342.] [343.] [344.] [345.] [346.] [347.] [348.] [349.] [350.] [351.] [352.] [353.]